Skoda OEM-Style Gloss Black Machined Face Forged Wheels
Monoblock · Gloss Black
2026 Skoda Elroq RS Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Skoda Elroq RS wheels? This page gives the 2026 Skoda Elroq RS bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Skoda Elroq RS rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2026 Skoda Elroq RS uses a 5x112 bolt pattern with a 57.1 mm centre bore and M14x1.5 lug bolts. For aftermarket wheels, 20x8J ET45 front / 20x8.5J ET45 rear sits flush.
Forged wheels for the 2026 Skoda Elroq RS — drilled 5x112 with a 57.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Skoda Elroq RS (2026): 5x112 bolt pattern, 57.1mm center bore, OE F 20x8J ET45 / R 20x8.5J ET45. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x112
Wheel Bolt/NutM14x1.5 Bolt
Center Bore57.1mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2026
Category5-Lug Large Sedan/SUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 20x8J ET45 / R 20x8.5J ET45 |
Forged Wheel Designs for the Skoda Elroq RS
Every design below is forged to order, so it can be machined to the Skoda Elroq RS's 5x112 bolt pattern and 57.1 mm center bore, with the width and offset calculated for your setup.
Skoda OEM-Style Black / Machined 5 V-Spoke Machined Face Forged Wheels
Monoblock · Black Machined
Babos Black / Machined Forged Wheels
Replica · Black Machined
Metallic Gray Split Forged Wheels
Monoblock · Metallic Gray
Bronze Mesh Concave Forged Wheels
Concave · Bronze
Brushed Silver Twisted 5-Spoke Forged Wheels
Monoblock · Brushed Silver
HRE Performance P200-Style Gloss Black 10 Y-Spoke Petal Forged Wheels
Replica · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Skoda Elroq RS ships from the factory on a 5x112 bolt pattern with a 57.1mm center bore and a F 20x8J ET45 / R 20x8.5J ET45 wheel. Our flush reference for the Skoda Elroq RS is 20x9J ET35.; our maximum aggressive reference is 21x9J ET30. — beyond that, expect clearance issues against the fender liner without further modification.
Skoda Elroq RS OE Wheel Specs
The Skoda Elroq RS ships from the factory on 5x112 bolt pattern wheels with a 57.1mm center bore. The stock wheel size is F 20x8J ET45 / R 20x8.5J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Skoda Elroq RS (2026) we drill the 5x112 pattern and cut the centre bore to 57.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 20x8J | ET45 | 6.27 in (159 mm) | — | — |
| Flush | 20x9J | ET35 | 6.38 in (162 mm) | +3 mm | +23 mm |
| Maximum | 21x9J | ET30 | 6.18 in (157 mm) | −2 mm | +28 mm |
Vehicles With the Same Hub as the Skoda Elroq RS (5x112, 57.1 mm Bore)
In our database, 407 other vehicle entries from 18 makes use exactly the same 5x112 bolt pattern and 57.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 29.0% of those also use a 57.1 mm center bore.
Hub-Centric Rings for a 57.1 mm Center Bore
A wheel with a center bore larger than 57.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 60.1 mm | 60.1 → 57.1 mm |
| 63.4 mm | 63.4 → 57.1 mm |
| 64.1 mm | 64.1 → 57.1 mm |
| 65.1 mm | 65.1 → 57.1 mm |
| 73.1 mm | 73.1 → 57.1 mm |
ANKUSI forged wheels are bored to exactly 57.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Skoda Elroq RS use?
The 2026 Skoda Elroq RS uses a 5x112 bolt pattern.
How many lug bolts does the Skoda Elroq RS use?
The Skoda Elroq RS uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Skoda Elroq RS?
The Skoda Elroq RS's center bore is 57.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the Skoda Elroq RS?
For a flush look with minimal to no rubbing, we recommend F 20x8J ET45 / R 20x8.5J ET45 as a starting point on a stock or mildly lowered Skoda Elroq RS.
Do I need wheel spacers for my Skoda Elroq RS?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Skoda Elroq RS?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.27" backspacing up front and 6.52" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Skoda Elroq RS?
Yes — the Skoda Elroq RS's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 20x8 wheels · 20 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.