Bright Silver 5 Y-Spoke Forged Wheels
Monoblock · Bright Silver
1970 Porsche 914/6 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Porsche 914/6 wheels? This page gives the 1970 Porsche 914/6 bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Porsche 914/6 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 1970 Porsche 914/6 uses a 5x130 bolt pattern with a 71.6 mm centre bore and M14x1.5 lug bolts. Factory wheels: F: 15x5.5J R: 15x5.5J. For aftermarket wheels, 15x7J ET20 sits flush and 15x8J ET6 is the most aggressive fit.
Forged wheels for the 1970 Porsche 914/6 — drilled 5x130 with a 71.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Porsche 914/6 (1970): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: F: 15x5.5J R: 15x5.5J. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating600–700 kg/wheel (Classic Sports Car segment reference)
Caliper TypeFixed 4-piston front caliper (OEM, shared with Porsche 911T)
Year1970
CategorySports Coupe
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 15x5.5J R: 15x5.5J |
| Flush Fitment | F 15x7J ET20 / R 15x7J ET20 |
| Maximum Aggressive | F 15x8J ET6 / R 15x8J ET6 |
Forged Wheel Designs for the Porsche 914/6
Every design below is forged to order, so it can be machined to the Porsche 914/6's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
Brox Gloss White 15-Spoke Deep Lip Forged Wheels
Deep Dish · Gloss White
BBS LM-Style Silver 10 Y-Spoke Polished Deep Lip Forged Wheels
Deep Dish · Silver
Porsche OEM-Style Gloss Black 5 Twin-Spoke Forged Wheels
Monoblock · Gloss Black
Wheelforce-Style Gloss Black 10 Directional-Spoke Forged Wheels
Monoblock · Gloss Black
Porsche 911 Turbo S Forged Wheels
Monoblock
Brushed Silver Slotted Dish Forged Wheels
Monoblock · Brushed Silver
HRE-Style Gunmetal Mesh Multi-Spoke Forged Wheels
Monoblock · Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Coupes and performance platforms are where rotational mass shows up fastest — in acceleration, in braking, and in how quickly the chassis changes direction. Forging lets us build to the same strength spec as the factory wheel at a meaningfully lower rotational weight, which is where the performance gain actually comes from, not just the visual one.
The Porsche 914/6 runs a 5x130 bolt pattern, 71.6mm center bore, and a F: 15x5.5J wheel from the factory. Our Flush Fitment reference is F 15x7J ET20 / R 15x7J ET20, which tucks the tire under the fender lip on a stock-height Porsche 914/6. Our Maximum Aggressive reference is F 15x8J ET6 / R 15x8J ET6 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Porsche 914/6 OE Wheel Specs
The 1970 Porsche 914/6 (Sports Coupe) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are F: 15x5.5J R: 15x5.5J.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche 914/6 (1970) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Real-World Fitment Notes
The 914/6 shares its front suspension, hubs and 5x130/71.6mm bolt pattern with the contemporary 911, so period-correct 911 Fuchs wheels bolt straight on — a direct-fit advantage the 4-cylinder 914-4 does not have. Deep-offset 15x8 Fuchs replicas around ET6 are a well-known aggressive reference for flared cars.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 15x5.5J ET23 → ~4.16″ F backspacing, R 15x5.5J ET23 → ~4.16″ R backspacing
- Flush: F 15x7J ET20 → ~4.79″ F backspacing, R 15x7J ET20 → ~4.79″ R backspacing
- Max: F 15x8J ET6 → ~4.74″ F backspacing, R 15x8J ET6 → ~4.74″ R backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche 914/6? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Porsche 914/6 (5x130, 71.6 mm Bore)
In our database, 294 other vehicle entries from 10 makes use exactly the same 5x130 bolt pattern and 71.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x130 is used by 5.8% of the vehicle pages in our English fitment guide (375 of 6,503); 78.7% of those also use a 71.6 mm center bore.
Hub-Centric Rings for a 71.6 mm Center Bore
A wheel with a center bore larger than 71.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 72.6 mm | 72.6 → 71.6 mm |
| 73.1 mm | 73.1 → 71.6 mm |
| 74.1 mm | 74.1 → 71.6 mm |
| 76.1 mm | 76.1 → 71.6 mm |
ANKUSI forged wheels are bored to exactly 71.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Porsche 914/6 use?
The 1970 Porsche 914/6 uses a 5x130 bolt pattern.
How many lug bolts does the Porsche 914/6 use?
The Porsche 914/6 uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Porsche 914/6?
The Porsche 914/6's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Porsche 914/6?
Factory wheels on the Porsche 914/6 are F: 15x5.5J R: 15x5.5J.
What is the biggest wheel size I can fit on my Porsche 914/6 without rubbing?
The most aggressive fitment we recommend without fender work is F 15x8J ET6 / R 15x8J ET6. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Porsche 914/6?
For a flush look with minimal to no rubbing, we recommend F 15x7J ET20 / R 15x7J ET20 as a starting point on a stock or mildly lowered Porsche 914/6.
Do I need wheel spacers for my Porsche 914/6?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Porsche 914/6?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 4.79" backspacing up front and 4.79" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Porsche 914/6?
Yes — the Porsche 914/6's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 15x5.5 wheels · 15 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.