Opel OEM-Style Gloss Black Multi-Spoke Forged Wheels
Monoblock · Gloss Black
2013 Opel Mokka Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Opel Mokka wheels? This page gives the 2013 Opel Mokka bolt pattern (5x105), centre bore, factory rim size and the offset range for aftermarket and forged Opel Mokka rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2013 Opel Mokka uses a 5x105 bolt pattern with a 56.6 mm centre bore and M12x1.5 lug nuts. Factory wheels: 18x7J ET38. For aftermarket wheels, 19x8J ET30 sits flush.
Forged wheels for the 2013 Opel Mokka — drilled 5x105 with a 56.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Opel Mokka (2013): 5x105 bolt pattern, 56.6mm center bore, OE 18x7J ET38. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x105
Wheel Bolt/NutM12x1.5 Nut
Center Bore56.6mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2013
Category5-Lug Standard Sedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x7J ET38 |
| Flush Fitment | 19x8J at ET30 offset |
Forged Wheel Designs for the Opel Mokka
Every design below is forged to order, so it can be machined to the Opel Mokka's 5x105 bolt pattern and 56.6 mm center bore, with the width and offset calculated for your setup.
Bronze 5 Y-Spoke Forged Wheels
Monoblock · Bronze
Orange Mesh Silver-Ring Beadlock Forged Wheels
Off-Road Beadlock · Orange
Gray 10 Y-Spoke Forged Wheels
Monoblock · Gray
APEX-Style Gold Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gold
HRE-Style Bronze 10-Spoke Forged Wheels
Monoblock · Bronze
Gloss White Full-Face Deep Lip Forged Wheels
Deep Dish · Gloss White
Forgiato Transparent Black / Gray Brushed Forged Wheels
Replica · Transparent Black / Gray
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Opel Mokka ships from the factory on a 5x105 bolt pattern with a 56.6mm center bore and a 18x7J ET38 wheel. Our flush reference for the Opel Mokka is 19x8J ET30.; our maximum aggressive reference is 20x8.5J ET25. — beyond that, expect clearance issues against the fender liner without further modification.
Opel Mokka OE Wheel Specs
The Opel Mokka ships from the factory on 5x105 bolt pattern wheels with a 56.6mm center bore. The stock wheel size is 18x7J ET38, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Opel Mokka (2013) we drill the 5x105 pattern and cut the centre bore to 56.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 18x7J | ET38 | 5.50 in (140 mm) | — | — |
| Flush | 19x8J | ET30 | 5.68 in (144 mm) | +5 mm | +21 mm |
| Maximum | 20x8.5J | ET25 | 5.73 in (146 mm) | +6 mm | +32 mm |
Vehicles With the Same Hub as the Opel Mokka (5x105, 56.6 mm Bore)
In our database, 36 other vehicle entries from 4 makes use exactly the same 5x105 bolt pattern and 56.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x105 is used by 0.6% of the vehicle pages in our English fitment guide (37 of 6,503); 100.0% of those also use a 56.6 mm center bore.
Hub-Centric Rings for a 56.6 mm Center Bore
A wheel with a center bore larger than 56.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 57.1 mm | 57.1 → 56.6 mm |
| 60.1 mm | 60.1 → 56.6 mm |
| 63.4 mm | 63.4 → 56.6 mm |
| 64.1 mm | 64.1 → 56.6 mm |
| 73.1 mm | 73.1 → 56.6 mm |
ANKUSI forged wheels are bored to exactly 56.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Opel Mokka use?
The 2013 Opel Mokka uses a 5x105 bolt pattern.
How many lug bolts does the Opel Mokka use?
The Opel Mokka uses a 5-lug bolt pattern (5x105), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Opel Mokka?
The Opel Mokka's center bore is 56.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Opel Mokka?
Factory wheels on the Opel Mokka are 18x7J ET38.
What does a flush wheel fitment look like on the Opel Mokka?
For a flush look with minimal to no rubbing, we recommend 19x8J at ET30 offset as a starting point on a stock or mildly lowered Opel Mokka.
Do I need wheel spacers for my Opel Mokka?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Opel Mokka?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.68" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Opel Mokka?
The Opel Mokka runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x7 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.