Bright Silver 4-Slot Dish Forged Wheels
Off-Road · Bright Silver
2004 Nissan Pathfinder Armada Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Nissan Pathfinder Armada wheels? This page gives the 2004 Nissan Pathfinder Armada bolt pattern (6x139.7), centre bore, factory rim size and the offset range for aftermarket and forged Nissan Pathfinder Armada rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2004 Nissan Pathfinder Armada uses a 6x139.7 bolt pattern with a 78.1 mm centre bore and M12x1.25 lug nuts. Factory wheels: 18x8J ET25. For aftermarket wheels, 18x9J ET12 sits flush.
Forged wheels for the 2004 Nissan Pathfinder Armada — drilled 6x139.7 with a 78.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Nissan Pathfinder Armada (2004): 6x139.7 bolt pattern, 78.1mm center bore, OE 18x8J ET25. Forged wheel fitment specs from ANKUSI.
Bolt Pattern6x139.7
Wheel Bolt/NutM12x1.25 Nut
Center Bore78.1mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2004
Category6-Lug Off-Road
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8J ET25 |
| Flush Fitment | 18x9J at ET12 offset |
Forged Wheel Designs for the Nissan Pathfinder Armada
Every design below is forged to order, so it can be machined to the Nissan Pathfinder Armada's 6x139.7 bolt pattern and 78.1 mm center bore, with the width and offset calculated for your setup.
Nissan OEM-Style Matte Black Custom Off-Road Forged Wheels
Off-Road · Matte Black
Fuel Silver Custom Beadlock Forged Wheels
Off-Road Beadlock · Silver
Black Mud-Style Silver / Gunmetal Slotted Rally Dish Off-Road Forged Wheels
Off-Road · Silver / Gunmetal
Nissan OEM-Style Gloss Black 10 Y-Spoke Off-Road Forged Wheels
Off-Road · Gloss Black
Nissan OEM-Style Gloss Black 10-Spoke Off-Road Forged Wheels
Off-Road · Custom Finish
Nissan OEM-Style Matte Black 6-Spoke Off-Road Beadlock Forged Wheels
Off-Road Beadlock · Matte Black
Nissan OEM-Style Black / Machined 6 Y-Spoke Off-Road Forged Wheels
Off-Road · Black Machined
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Off-road platforms put real, repeated impact loads through the wheel that street-only vehicles never see, so the factory strength margin on the Nissan Pathfinder Armada isn't a formality — it's load-bearing in a literal sense. Forging matches that margin at a lower rotational weight than an equivalent cast wheel, which matters both on the trail and on the highway miles between trailheads.
The Nissan Pathfinder Armada ships from the factory on a 6x139.7 bolt pattern with a 78.1mm center bore and a 18x8J ET25 wheel. Our flush reference for the Nissan Pathfinder Armada is 18x9J ET12.; our maximum aggressive reference is 20x10J ET0. — beyond that, expect clearance issues against the fender liner without further modification.
Nissan Pathfinder Armada OE Wheel Specs
The Nissan Pathfinder Armada ships from the factory on 6x139.7 bolt pattern wheels with a 78.1mm center bore. The stock wheel size is 18x8J ET25, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Nissan Pathfinder Armada (2004) we drill the 6x139.7 pattern and cut the centre bore to 78.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 18x8J | ET25 | 5.48 in (139 mm) | — | — |
| Flush | 18x9J | ET12 | 5.47 in (139 mm) | 0 mm | +26 mm |
| Maximum | 20x10J | ET0 | 5.50 in (140 mm) | 0 mm | +50 mm |
Vehicles With the Same Hub as the Nissan Pathfinder Armada (6x139.7, 78.1 mm Bore)
In our database, 79 other vehicle entries from 6 makes use exactly the same 6x139.7 bolt pattern and 78.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
6x139.7 is used by 4.0% of the vehicle pages in our English fitment guide (258 of 6,503); 31.0% of those also use a 78.1 mm center bore.
Hub-Centric Rings for a 78.1 mm Center Bore
A wheel with a center bore larger than 78.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 84.1 mm | 84.1 → 78.1 mm |
| 93.1 mm | 93.1 → 78.1 mm |
| 100.1 mm | 100.1 → 78.1 mm |
| 106.1 mm | 106.1 → 78.1 mm |
ANKUSI forged wheels are bored to exactly 78.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Nissan Pathfinder Armada use?
The 2004 Nissan Pathfinder Armada uses a 6x139.7 bolt pattern.
How many lug bolts does the Nissan Pathfinder Armada use?
The Nissan Pathfinder Armada uses a 6-lug bolt pattern (6x139.7), so you need a 6-lug forged wheel to bolt straight on.
What is the center bore size on the Nissan Pathfinder Armada?
The Nissan Pathfinder Armada's center bore is 78.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Nissan Pathfinder Armada?
Factory wheels on the Nissan Pathfinder Armada are 18x8J ET25.
What does a flush wheel fitment look like on the Nissan Pathfinder Armada?
For a flush look with minimal to no rubbing, we recommend 18x9J at ET12 offset as a starting point on a stock or mildly lowered Nissan Pathfinder Armada.
Do I need wheel spacers for my Nissan Pathfinder Armada?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Nissan Pathfinder Armada?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.47" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Nissan Pathfinder Armada?
The Nissan Pathfinder Armada runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.25, conical-seat lug nut.
Factory Torque Spec: 103-122 Nm (76-90 ft-lb). Range covers most Nissan passenger cars and crossovers on M12x1.25 studs.
TPMS: Vehicles built before the 2008 model year were not federally required to carry factory TPMS in the US, though many manufacturers adopted it earlier; verify whether your specific build has TPMS before ordering sensor-compatible wheels.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x8 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.