
Bronze Gold Cross-Spoke Forged Wheels
Monoblock · Bronze Gold
Fitting Nissan Micra 160SR wheels? This page gives the 2005 Nissan Micra 160SR bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Nissan Micra 160SR rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Nissan Micra — styles, sizes & factory quote →
Nissan Micra 160SR (2005): 4x100 bolt pattern, 60.1mm center bore. Factory wheels: 16x6.0J at ET45 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 16x6.0J F/R |
| Flush Fitment | 16x7.0J at ET35 offset |
| Maximum Aggressive | 17x7.5J at ET30 offset |
Every design below is forged to order, so it can be machined to the Nissan Micra 160SR's 4x100 bolt pattern and 60.1 mm center bore, with the width and offset calculated for your setup.

Monoblock · Bronze Gold

Monoblock · Black Machined

Deep Dish · Gunmetal

Monoblock · Gloss White

Monoblock · Bright Silver

Monoblock · Silver

Monoblock · Matte Bronze

Monoblock · Gloss White
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


On a compact performance platform, every pound of rotational mass fights the car's natural agility. A forged wheel keeps strength at the factory-rated level while cutting that rotational weight, which is where the driving-feel improvement actually comes from.
The Nissan Micra 160SR runs a 4x100 bolt pattern, 60.1mm center bore, and a 16x6.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 16x7.0J ET35, which tucks the tire under the fender lip on a stock-height Nissan Micra 160SR. Our Maximum Aggressive reference is 17x7.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2005 Nissan Micra 160SR (Hot Hatch) uses a 4x100 bolt pattern with a 60.1mm center bore. Factory wheels are 16x6.0J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Nissan Micra 160SR (2005) we drill the 4x100 pattern and cut the centre bore to 60.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Nissan spec, or want a wheel built to a custom offset for your Nissan Micra 160SR? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.