
Rays-Style Metallic Gray 5 Y-Spoke Forged Wheels
Replica · Metallic Gray
Fitting Nissan Juke Hybrid wheels? This page gives the 2022 Nissan Juke Hybrid bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Nissan Juke Hybrid rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Nissan Juke Hybrid (2022): 5x114.3 bolt pattern, 66.1mm center bore. Factory wheels: 19x7.5J at ET35 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x7.5J F/R |
| Flush Fitment | 19x8.5J at ET28 offset |
| Maximum Aggressive | 20x8.5J at ET25 offset |
Every design below is forged to order, so it can be machined to the Nissan Juke Hybrid's 5x114.3 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.

Replica · Metallic Gray

Monoblock · Black Chrome

Replica · Gloss Black

Monoblock · Gloss Black

2-Piece · Matte Black

Replica · Gray Green

Monoblock · Chrome

Deep Dish · Brushed Silver
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Nissan Juke Hybrid runs a 5x114.3 bolt pattern, 66.1mm center bore, and a 19x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.5J ET28, which tucks the tire under the fender lip on a stock-height Nissan Juke Hybrid. Our Maximum Aggressive reference is 20x8.5J ET25 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2022 Nissan Juke Hybrid (Hybrid Crossover) uses a 5x114.3 bolt pattern with a 66.1mm center bore. Factory wheels are 19x7.5J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Nissan Juke Hybrid (2022) we drill the 5x114.3 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Nissan spec, or want a wheel built to a custom offset for your Nissan Juke Hybrid? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.