
Advan-Style Bronze 5-Spoke Polished Lip Forged Wheels
Monoblock · Bronze
Fitting Nissan GT-R 50th Anniversary Edition wheels? This page gives the 2020 Nissan GT-R 50th Anniversary Edition bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Nissan GT-R 50th Anniversary Edition rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Nissan GT-R — styles, sizes & factory quote →
Nissan GT-R 50th Anniversary Edition (2020): 5x114.3 bolt pattern, 66.1mm center bore. Factory wheels: F: 20x9.5J R: 20x10.5J. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 20x9.5J R: 20x10.5J |
| Flush Fitment | F 20x10.0J ET30 / R 20x11.0J ET15 |
| Maximum Aggressive | F 20x10.5J ET25 / R 20x11.5J ET10 |
Every design below is forged to order, so it can be machined to the Nissan GT-R 50th Anniversary Edition's 5x114.3 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.

Monoblock · Bronze

Replica · Bright Blue

Replica · Brushed Silver

Replica · Bright Silver

Replica · Bronze

Monoblock · Satin Black

2-Piece · Gunmetal

Replica · Bronze
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


On a supercar, wheel weight is one of the few remaining places to cut rotational mass without touching the powertrain or chassis the factory already optimized. Forging gets there at the same structural margin as the OE wheel, which is exactly the trade a car built around outright performance rewards.
The Nissan GT-R 50th Anniversary Edition runs a 5x114.3 bolt pattern, 66.1mm center bore, and a F: 20x9.5J wheel from the factory. Our Flush Fitment reference is F 20x10.0J ET30 / R 20x11.0J ET15, which tucks the tire under the fender lip on a stock-height Nissan GT-R 50th Anniversary Edition. Our Maximum Aggressive reference is F 20x10.5J ET25 / R 20x11.5J ET10 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2020 Nissan GT-R 50th Anniversary Edition (Supercar) uses a 5x114.3 bolt pattern with a 66.1mm center bore. Factory wheels are F: 20x9.5J R: 20x10.5J.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Nissan GT-R 50th Anniversary Edition (2020) we drill the 5x114.3 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Nissan spec, or want a wheel built to a custom offset for your Nissan GT-R 50th Anniversary Edition? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Thread & Fastener: M12x1.25, conical-seat lug nut.
Factory Torque Spec: 103-122 Nm (76-90 ft-lb). Range covers most Nissan passenger cars and crossovers on M12x1.25 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.