Mazda OEM-Style Gunmetal 10-Spoke Forged Wheels
Monoblock · Gunmetal
2009 Mazda 6 SAP Wagon Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Mazda 6 SAP Wagon wheels? This page gives the 2009 Mazda 6 SAP Wagon bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Mazda 6 SAP Wagon rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2009 Mazda 6 SAP Wagon uses a 5x114.3 bolt pattern with a 67.1 mm centre bore and M12x1.5 lug nuts. Factory wheels: 18x8J ET60. For aftermarket wheels, 19x8.5J ET45 sits flush.
Forged wheels for the 2009 Mazda 6 SAP Wagon — drilled 5x114.3 with a 67.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Mazda 6 SAP Wagon (2009): 5x114.3 bolt pattern, 67.1mm center bore, OE 18x8J ET60. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore67.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2009
Category5-Lug Performance / Tuner
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8J ET60 |
| Flush Fitment | 19x8.5J at ET45 offset |
Forged Wheel Designs for the Mazda 6 SAP Wagon
Every design below is forged to order, so it can be machined to the Mazda 6 SAP Wagon's 5x114.3 bolt pattern and 67.1 mm center bore, with the width and offset calculated for your setup.
Polished Silver 6-Spoke Deep Lip Forged Wheels
Deep Dish · Polished Silver
Vossen HF-7-Style Brushed Silver 5 W-Spoke Side-Milled Forged Wheels
Replica · Brushed Silver
Matte Silver 10-Spoke Forged Wheels
Monoblock · Matte Silver
Matte Silver 5-Spoke Machined Face Forged Wheels
Monoblock · Matte Silver
Chrome 10 Y-Spoke Forged Wheels
Monoblock · Chrome
Bright Silver Full-Face 7-Spoke Forged Wheels
Monoblock · Bright Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A wagon carries wagon-specific weight distribution — more mass over the rear axle when loaded — so wheel strength at the rear corners matters as much as the front. Forging lets us match the factory's strength target on both ends while keeping rotational mass down, which keeps the ride composed whether the cargo area is empty or full.
The Mazda 6 SAP Wagon ships from the factory on a 5x114.3 bolt pattern with a 67.1mm center bore and a 18x8J ET60 wheel. Our flush reference for the Mazda 6 SAP Wagon is 19x8.5J ET45.; our maximum aggressive reference is 20x9J ET40. — beyond that, expect clearance issues against the fender liner without further modification.
Mazda 6 SAP Wagon OE Wheel Specs
The Mazda 6 SAP Wagon ships from the factory on 5x114.3 bolt pattern wheels with a 67.1mm center bore. The stock wheel size is 18x8J ET60, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Mazda 6 SAP Wagon (2009) we drill the 5x114.3 pattern and cut the centre bore to 67.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 18x8J | ET60 | 6.86 in (174 mm) | — | — |
| Flush | 19x8.5J | ET45 | 6.52 in (166 mm) | −9 mm | +21 mm |
| Maximum | 20x9J | ET40 | 6.57 in (167 mm) | −7 mm | +33 mm |
Vehicles With the Same Hub as the Mazda 6 SAP Wagon (5x114.3, 67.1 mm Bore)
In our database, 456 other vehicle entries from 30 makes use exactly the same 5x114.3 bolt pattern and 67.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 35.2% of those also use a 67.1 mm center bore.
Hub-Centric Rings for a 67.1 mm Center Bore
A wheel with a center bore larger than 67.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 70.1 mm | 70.1 → 67.1 mm |
| 70.5 mm | 70.5 → 67.1 mm |
| 71.6 mm | 71.6 → 67.1 mm |
| 72.6 mm | 72.6 → 67.1 mm |
| 73.1 mm | 73.1 → 67.1 mm |
ANKUSI forged wheels are bored to exactly 67.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Mazda 6 SAP Wagon use?
The 2009 Mazda 6 SAP Wagon uses a 5x114.3 bolt pattern.
How many lug bolts does the Mazda 6 SAP Wagon use?
The Mazda 6 SAP Wagon uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Mazda 6 SAP Wagon?
The Mazda 6 SAP Wagon's center bore is 67.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Mazda 6 SAP Wagon?
Factory wheels on the Mazda 6 SAP Wagon are 18x8J ET60.
What does a flush wheel fitment look like on the Mazda 6 SAP Wagon?
For a flush look with minimal to no rubbing, we recommend 19x8.5J at ET45 offset as a starting point on a stock or mildly lowered Mazda 6 SAP Wagon.
Do I need wheel spacers for my Mazda 6 SAP Wagon?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Mazda 6 SAP Wagon?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.52" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Mazda 6 SAP Wagon?
The Mazda 6 SAP Wagon runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x8 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.