2013 Hyundai Langdong Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Hyundai Langdong wheels? This page gives the 2013 Hyundai Langdong bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Hyundai Langdong rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2013 Hyundai Langdong uses a 5x114.3 bolt pattern with a 67.1 mm centre bore and M12x1.5 lug nuts. Factory wheels: 17x7J ET45. For aftermarket wheels, 18x8J ET40 sits flush.
Forged wheels for the 2013 Hyundai Langdong — drilled 5x114.3 with a 67.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Hyundai Langdong (2013): 5x114.3 bolt pattern, 67.1mm center bore, OE 17x7J ET45. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore67.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2013
Category5-Lug Performance / Tuner
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x7J ET45 |
| Flush Fitment | 18x8J at ET40 offset |
Forged Wheel Designs for the Hyundai Langdong
Every design below is forged to order, so it can be machined to the Hyundai Langdong's 5x114.3 bolt pattern and 67.1 mm center bore, with the width and offset calculated for your setup.
Vossen HF-2-Style Gloss Black 10 Y-Spoke Machined Face Forged Wheels
Replica · Gloss Black
Matte Silver Directional Milled Machined Face Forged Wheels
Monoblock · Matte Silver
Satin Gunmetal 5-Spoke Forged Wheels
Monoblock · Satin Gunmetal
Hyundai N Style Matte Silver Split-Spoke Machined Face Forged Wheels
Monoblock · Matte Silver
OZ Racing-Style Polished Turbofan Dish Riveted Lip Forged Wheels
2-Piece · Polished
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Most of the engineering value in a forged wheel over a cast one shows up in rotational mass, not outright strength — both can meet the same load rating, but the forged piece gets there lighter. On a sedan platform tuned for everyday balance, that weight saving is felt directly in steering response and ride quality.
The Hyundai Langdong ships from the factory on a 5x114.3 bolt pattern with a 67.1mm center bore and a 17x7J ET45 wheel. Our flush reference for the Hyundai Langdong is 18x8J ET40.; our maximum aggressive reference is 19x8.5J ET38. — beyond that, expect clearance issues against the fender liner without further modification.
Hyundai Langdong OE Wheel Specs
The Hyundai Langdong ships from the factory on 5x114.3 bolt pattern wheels with a 67.1mm center bore. The stock wheel size is 17x7J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Hyundai Langdong (2013) we drill the 5x114.3 pattern and cut the centre bore to 67.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 17x7J | ET45 | 5.77 in (147 mm) | — | — |
| Flush | 18x8J | ET40 | 6.07 in (154 mm) | +8 mm | +18 mm |
| Maximum | 19x8.5J | ET38 | 6.25 in (159 mm) | +12 mm | +26 mm |
Vehicles With the Same Hub as the Hyundai Langdong (5x114.3, 67.1 mm Bore)
In our database, 456 other vehicle entries from 30 makes use exactly the same 5x114.3 bolt pattern and 67.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 35.2% of those also use a 67.1 mm center bore.
Hub-Centric Rings for a 67.1 mm Center Bore
A wheel with a center bore larger than 67.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 70.1 mm | 70.1 → 67.1 mm |
| 70.5 mm | 70.5 → 67.1 mm |
| 71.6 mm | 71.6 → 67.1 mm |
| 72.6 mm | 72.6 → 67.1 mm |
| 73.1 mm | 73.1 → 67.1 mm |
ANKUSI forged wheels are bored to exactly 67.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Hyundai Langdong use?
The 2013 Hyundai Langdong uses a 5x114.3 bolt pattern.
How many lug bolts does the Hyundai Langdong use?
The Hyundai Langdong uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Hyundai Langdong?
The Hyundai Langdong's center bore is 67.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Hyundai Langdong?
Factory wheels on the Hyundai Langdong are 17x7J ET45.
What does a flush wheel fitment look like on the Hyundai Langdong?
For a flush look with minimal to no rubbing, we recommend 18x8J at ET40 offset as a starting point on a stock or mildly lowered Hyundai Langdong.
Do I need wheel spacers for my Hyundai Langdong?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Hyundai Langdong?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.07" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Hyundai Langdong?
The Hyundai Langdong runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 17x7 wheels · 17 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.