
2012 Kia Rio Sedan Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Kia Rio Sedan wheels? This page gives the 2012 Kia Rio Sedan bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Kia Rio Sedan rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Kia Rio Sedan (2012): 4x100 bolt pattern, 54.1mm center bore. Factory wheels: 17x6.5J F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x6.5J F/R |
| Flush Fitment | 18x7.5J at ET38 offset |
| Maximum Aggressive | 18x8.0J at ET35 offset |
Forged Wheel Designs for the Kia Rio Sedan
Every design below is forged to order, so it can be machined to the Kia Rio Sedan's 4x100 bolt pattern and 54.1 mm center bore, with the width and offset calculated for your setup.


Rotiform-Style Gloss White 6-Spoke Forged Wheels
Monoblock · Gloss White

BBS LM-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal

BBS-Style Gold Mesh Polished Lip 2-Piece Forged Wheels
2-Piece · Gold

BBS-Style Gold Mesh Polished Lip Forged Wheels
Monoblock · Gold

OZ Racing-Style Gloss White 15-Spoke Forged Wheels
Monoblock · Gloss White

Bronze Gold Cross-Spoke Forged Wheels
Monoblock · Bronze Gold

Rays-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


ANKUSI Engineering Expert Advice
The Kia Rio Sedan's factory wheel spec reflects a deliberate balance between comfort, steering feel and durability that the engineering team tuned for. Forging lets ANKUSI match that same strength target while trimming rotational mass — the part of a wheel upgrade that actually changes how the car drives, not just how it looks.
The Kia Rio Sedan runs a 4x100 bolt pattern, 54.1mm center bore, and a 17x6.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x7.5J ET38, which tucks the tire under the fender lip on a stock-height Kia Rio Sedan. Our Maximum Aggressive reference is 18x8.0J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Kia Rio Sedan OE Wheel Specs
The 2012 Kia Rio Sedan (Sedan) uses a 4x100 bolt pattern with a 54.1mm center bore. Factory wheels are 17x6.5J F/R.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Kia Rio Sedan (2012) we drill the 4x100 pattern and cut the centre bore to 54.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 17x6.5J ET45 → ~5.52″ backspacing
- Flush: 18x7.5J ET38 → ~5.75″ backspacing
- Max: 18x8.0J ET35 → ~5.88″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Kia spec, or want a wheel built to a custom offset for your Kia Rio Sedan? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Kia Rio Sedan use?
How many lug bolts does the Kia Rio Sedan use?
What is the center bore size on the Kia Rio Sedan?
What size are the factory (stock) wheels on the Kia Rio Sedan?
What is the biggest wheel size I can fit on my Kia Rio Sedan without rubbing?
What does a flush wheel fitment look like on the Kia Rio Sedan?
Do I need wheel spacers for my Kia Rio Sedan?
How do I calculate wheel backspacing for my Kia Rio Sedan?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Kia Rio Sedan?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 107-127 Nm (79-94 ft-lb). Range covers most Kia passenger cars and crossovers on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.