
OZ Racing-Style Gloss White 15-Spoke Forged Wheels
Monoblock · Gloss White
Fitting Kia Ray EV wheels? This page gives the 2012 Kia Ray EV bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Kia Ray EV rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Kia Ray EV (2012): 4x100 bolt pattern, 54.1mm center bore. Factory wheels: 14x5.0J F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 14x5.0J F/R |
| Flush Fitment | 15x6.0J at ET40 offset |
| Maximum Aggressive | 16x6.5J at ET38 offset |
Every design below is forged to order, so it can be machined to the Kia Ray EV's 4x100 bolt pattern and 54.1 mm center bore, with the width and offset calculated for your setup.

Monoblock · Gloss White

Monoblock · Bronze Gold

Deep Dish · Gunmetal

Monoblock · Matte Bronze

Monoblock · Black Machined

Monoblock · Bright Silver

Monoblock · Silver

Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


Minivans carry passengers and cargo across a wide range of loaded conditions, so the factory wheel spec is built around a conservative load margin. Forging lets us hold that same margin while trimming rotational mass, which shows up as smoother ride quality whether the vehicle is empty or fully loaded.
The Kia Ray EV runs a 4x100 bolt pattern, 54.1mm center bore, and a 14x5.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 15x6.0J ET40, which tucks the tire under the fender lip on a stock-height Kia Ray EV. Our Maximum Aggressive reference is 16x6.5J ET38 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2012 Kia Ray EV (EV Minivan) uses a 4x100 bolt pattern with a 54.1mm center bore. Factory wheels are 14x5.0J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Kia Ray EV (2012) we drill the 4x100 pattern and cut the centre bore to 54.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Kia spec, or want a wheel built to a custom offset for your Kia Ray EV? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 107-127 Nm (79-94 ft-lb). Range covers most Kia passenger cars and crossovers on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.