
2018 Kia Rio GT-Line Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Kia Rio GT-Line wheels? This page gives the 2018 Kia Rio GT-Line bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Kia Rio GT-Line rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Kia Rio GT-Line (2018): 4x100 bolt pattern, 54.1mm center bore. Factory wheels: 17x6.5J F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x6.5J F/R |
| Flush Fitment | 18x7.5J at ET38 offset |
| Maximum Aggressive | 18x8.0J at ET35 offset |
Forged Wheel Designs for the Kia Rio GT-Line
Every design below is forged to order, so it can be machined to the Kia Rio GT-Line's 4x100 bolt pattern and 54.1 mm center bore, with the width and offset calculated for your setup.


BBS LM-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal

Rotiform-Style Gloss White 6-Spoke Forged Wheels
Monoblock · Gloss White

BBS-Style Gold Mesh Polished Lip Forged Wheels
Monoblock · Gold

BBS-Style Gold Mesh Polished Lip 2-Piece Forged Wheels
2-Piece · Gold

Bronze Gold Cross-Spoke Forged Wheels
Monoblock · Bronze Gold

OZ Racing-Style Gloss White 15-Spoke Forged Wheels
Monoblock · Gloss White

Rays-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


ANKUSI Engineering Expert Advice
Hot hatches and performance compacts are built around quick direction changes, so rotational mass at the wheel has an outsized effect on how the car actually feels to drive. Forging trims that mass while holding the same strength margin as the factory wheel, which is exactly the trade-off this kind of platform rewards.
The Kia Rio GT-Line runs a 4x100 bolt pattern, 54.1mm center bore, and a 17x6.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x7.5J ET38, which tucks the tire under the fender lip on a stock-height Kia Rio GT-Line. Our Maximum Aggressive reference is 18x8.0J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Kia Rio GT-Line OE Wheel Specs
The 2018 Kia Rio GT-Line (Hatchback) uses a 4x100 bolt pattern with a 54.1mm center bore. Factory wheels are 17x6.5J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Kia Rio GT-Line (2018) we drill the 4x100 pattern and cut the centre bore to 54.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 17x6.5J ET45 → ~5.52″ backspacing
- Flush: 18x7.5J ET38 → ~5.75″ backspacing
- Max: 18x8.0J ET35 → ~5.88″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Kia spec, or want a wheel built to a custom offset for your Kia Rio GT-Line? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Kia Rio GT-Line use?
How many lug bolts does the Kia Rio GT-Line use?
What is the center bore size on the Kia Rio GT-Line?
What size are the factory (stock) wheels on the Kia Rio GT-Line?
What is the biggest wheel size I can fit on my Kia Rio GT-Line without rubbing?
What does a flush wheel fitment look like on the Kia Rio GT-Line?
Do I need wheel spacers for my Kia Rio GT-Line?
How do I calculate wheel backspacing for my Kia Rio GT-Line?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Kia Rio GT-Line?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 107-127 Nm (79-94 ft-lb). Range covers most Kia passenger cars and crossovers on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.