Wheelforce-Style Transparent Gray Brushed 10-Spoke Star Forged Wheels
Monoblock · Transparent Gray
2008 Infiniti EX35 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Infiniti EX35 wheels? This page gives the 2008 Infiniti EX35 bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Infiniti EX35 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2008 Infiniti EX35 uses a 5x114.3 bolt pattern with a 66.1 mm centre bore and M12x1.25 lug nuts. Factory wheels: 18x8J at ET47. For aftermarket wheels, 19x8.5J ET35 sits flush and 20x9J ET30 is the most aggressive fit.
Forged wheels for the 2008 Infiniti EX35 — drilled 5x114.3 with a 66.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Infiniti EX35 (2008): 5x114.3 bolt pattern, 66.1mm center bore. Factory wheels: 18x8J. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.25 Nut
Center Bore66.1mm
Wheel Load Rating800–950 kg/wheel (Crossover segment reference)
Year2008
CategoryCrossover
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8J at ET47 |
| Flush Fitment | 19x8.5J at ET35 offset |
| Maximum Aggressive | 20x9J at ET30 offset |
Forged Wheel Designs for the Infiniti EX35
Every design below is forged to order, so it can be machined to the Infiniti EX35's 5x114.3 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.
Advan-Style Bronze 5-Spoke Polished Lip Forged Wheels
Monoblock · Bronze
Vossen LC3-01T-Style Brushed Silver 5-Spoke Forged Wheels
Replica · Brushed Silver
Wheelforce-Style Matte Silver 10-Spoke Star Forged Wheels
Monoblock · Matte Silver
Chrome 5 Y-Spoke Forged Wheels
Monoblock · Chrome
Brushed Silver 5 Y-Spoke Polished Deep Lip Forged Wheels
Deep Dish · Brushed Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Infiniti EX35's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Infiniti EX35 runs a 5x114.3 bolt pattern, 66.1mm center bore, and a 18x8J at ET47, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.5J ET35, which tucks the tire under the fender lip on a stock-height Infiniti EX35. Our Maximum Aggressive reference is 20x9J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Infiniti EX35 OE Wheel Specs
The 2008 Infiniti EX35 (Crossover) uses a 5x114.3 bolt pattern with a 66.1mm center bore. Factory wheels are 18x8J at ET47.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Infiniti EX35 (2008) we drill the 5x114.3 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Real-World Fitment Notes
Chassis: Lowering springs. Tires: 225/55 R18.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x8J ET47 → ~6.35″ backspacing
- Flush: 19x8.5J ET35 → ~6.13″ backspacing
- Max: 20x9J ET30 → ~6.18″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Infiniti spec, or want a wheel built to a custom offset for your Infiniti EX35? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Infiniti EX35 (5x114.3, 66.1 mm Bore)
In our database, 224 other vehicle entries from 9 makes use exactly the same 5x114.3 bolt pattern and 66.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 17.3% of those also use a 66.1 mm center bore.
Hub-Centric Rings for a 66.1 mm Center Bore
A wheel with a center bore larger than 66.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 66.6 mm | 66.6 → 66.1 mm |
| 67.1 mm | 67.1 → 66.1 mm |
| 70.1 mm | 70.1 → 66.1 mm |
| 70.5 mm | 70.5 → 66.1 mm |
| 73.1 mm | 73.1 → 66.1 mm |
ANKUSI forged wheels are bored to exactly 66.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Infiniti EX35 use?
The 2008 Infiniti EX35 uses a 5x114.3 bolt pattern.
How many lug bolts does the Infiniti EX35 use?
The Infiniti EX35 uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Infiniti EX35?
The Infiniti EX35's center bore is 66.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Infiniti EX35?
Factory wheels on the Infiniti EX35 are 18x8J at ET47.
What is the biggest wheel size I can fit on my Infiniti EX35 without rubbing?
The most aggressive fitment we recommend without fender work is 20x9J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Infiniti EX35?
For a flush look with minimal to no rubbing, we recommend 19x8.5J at ET35 offset as a starting point on a stock or mildly lowered Infiniti EX35.
Do I need wheel spacers for my Infiniti EX35?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Infiniti EX35?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.13" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Infiniti EX35?
The Infiniti EX35 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x8 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.