2013 Hyundai Genesis Coupe Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Hyundai Genesis Coupe wheels? This page gives the 2013 Hyundai Genesis Coupe bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Hyundai Genesis Coupe rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2013 Hyundai Genesis Coupe uses a 5x114.3 bolt pattern with a 67.1 mm centre bore and M12x1.5 lug nuts. For aftermarket wheels, 19x8.5J ET25 front / 19x9.5J ET25 rear sits flush.
Forged wheels for the 2013 Hyundai Genesis Coupe — drilled 5x114.3 with a 67.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Hyundai Genesis Coupe (2013): 5x114.3 bolt pattern, 67.1mm center bore, OE F 18x7.5J ET35 / R 18x8J ET35. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore67.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2013
Category5-Lug Performance / Tuner
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 19x8.5J ET25 / R 19x9.5J ET25 |
Forged Wheel Designs for the Hyundai Genesis Coupe
Every design below is forged to order, so it can be machined to the Hyundai Genesis Coupe's 5x114.3 bolt pattern and 67.1 mm center bore, with the width and offset calculated for your setup.
OZ Racing-Style Polished Turbofan Dish Riveted Lip Forged Wheels
2-Piece · Polished
Vossen HF-5-Style Gloss Black Cross-Spoke Petal Forged Wheels
Replica · Gloss Black
Vossen Gloss Black / Silver 2-Piece Deep Lip Forged Wheels
2-Piece · Gloss Black / Silver
Hyundai N Style Matte Silver Split-Spoke Machined Face Forged Wheels
Monoblock · Matte Silver
Hyundai N Style LF Black Machined 5-Spoke Y-Design Forged Wheels
Replica · Black Machined
Satin Gunmetal 5-Spoke Forged Wheels
Monoblock · Satin Gunmetal
EvoCorse-Style Satin Black 12-Spoke Rally Forged Wheels
Monoblock · Satin Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Coupes and performance platforms are where rotational mass shows up fastest — in acceleration, in braking, and in how quickly the chassis changes direction. Forging lets us build to the same strength spec as the factory wheel at a meaningfully lower rotational weight, which is where the performance gain actually comes from, not just the visual one.
The Hyundai Genesis Coupe ships from the factory on a 5x114.3 bolt pattern with a 67.1mm center bore and a F 18x7.5J ET35 / R 18x8J ET35 wheel. Our flush reference for the Hyundai Genesis Coupe is F 19x8.5J ET25 / R 19x9.5J ET25.; our maximum aggressive reference is F 19x9.5J ET20 / R 19x10.5J ET20. — beyond that, expect clearance issues against the fender liner without further modification.
Hyundai Genesis Coupe OE Wheel Specs
The Hyundai Genesis Coupe ships from the factory on 5x114.3 bolt pattern wheels with a 67.1mm center bore. The stock wheel size is F 18x7.5J ET35 / R 18x8J ET35, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Hyundai Genesis Coupe (2013) we drill the 5x114.3 pattern and cut the centre bore to 67.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 18x7.5J | ET35 | 5.63 in (143 mm) | — | — |
| Flush | 19x8.5J | ET25 | 5.73 in (146 mm) | +3 mm | +23 mm |
| Maximum | 19x9.5J | ET20 | 6.04 in (153 mm) | +10 mm | +40 mm |
Vehicles With the Same Hub as the Hyundai Genesis Coupe (5x114.3, 67.1 mm Bore)
In our database, 456 other vehicle entries from 30 makes use exactly the same 5x114.3 bolt pattern and 67.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 35.2% of those also use a 67.1 mm center bore.
Hub-Centric Rings for a 67.1 mm Center Bore
A wheel with a center bore larger than 67.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 70.1 mm | 70.1 → 67.1 mm |
| 70.5 mm | 70.5 → 67.1 mm |
| 71.6 mm | 71.6 → 67.1 mm |
| 72.6 mm | 72.6 → 67.1 mm |
| 73.1 mm | 73.1 → 67.1 mm |
ANKUSI forged wheels are bored to exactly 67.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Hyundai Genesis Coupe use?
The 2013 Hyundai Genesis Coupe uses a 5x114.3 bolt pattern.
How many lug bolts does the Hyundai Genesis Coupe use?
The Hyundai Genesis Coupe uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Hyundai Genesis Coupe?
The Hyundai Genesis Coupe's center bore is 67.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the Hyundai Genesis Coupe?
For a flush look with minimal to no rubbing, we recommend F 19x8.5J ET25 / R 19x9.5J ET25 as a starting point on a stock or mildly lowered Hyundai Genesis Coupe.
Do I need wheel spacers for my Hyundai Genesis Coupe?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Hyundai Genesis Coupe?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.73" backspacing up front and 6.23" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Hyundai Genesis Coupe?
Yes — the Hyundai Genesis Coupe's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x7.5 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.