White / Black 6 Twin-Spoke Forged Wheels
Monoblock · White / Black
2011 Hamann BMW 5-Series F10 M-Technik Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Hamann BMW 5-Series F10 M-Technik wheels? This page gives the 2011 Hamann BMW 5-Series F10 M-Technik bolt pattern (5x120), centre bore, factory rim size and the offset range for aftermarket and forged Hamann BMW 5-Series F10 M-Technik rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2011 Hamann BMW 5-Series F10 M-Technik uses a 5x120 bolt pattern with a 72.6 mm centre bore and M12x1.5 lug bolts. Factory wheels: 19x8.5J ET33. For aftermarket wheels, 20x9J ET25 sits flush.
Forged wheels for the 2011 Hamann BMW 5-Series F10 M-Technik — drilled 5x120 with a 72.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Hamann BMW 5-Series F10 M-Technik (2011): 5x120 bolt pattern, 72.6mm center bore, OE 19x8.5J ET33. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x120
Wheel Bolt/NutM12x1.5 Bolt
Center Bore72.6mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2011
Category5-Lug Performance / Tuner
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x8.5J ET33 |
| Flush Fitment | 20x9J at ET25 offset |
Forged Wheel Designs for the Hamann BMW 5-Series F10 M-Technik
Every design below is forged to order, so it can be machined to the Hamann BMW 5-Series F10 M-Technik's 5x120 bolt pattern and 72.6 mm center bore, with the width and offset calculated for your setup.
Rohana-Style Orange 6 Y-Spoke Riveted Bolt Detail Forged Wheels
Deep Dish · Orange
Brushed Silver 5 Split-Spoke Forged Wheels
Monoblock · Brushed Silver
Gloss Black Twisted Petal-Spoke Forged Wheels
Monoblock · Gloss Black
Yellow / Black 5 Twin-Spoke Forged Wheels
Monoblock · Gloss Black
Metallic Gray 5 W-Spoke Forged Wheels
Monoblock · Metallic Gray
Bradley-Style Matte Black 5-Spoke Off-Road Forged Wheels
Off-Road · Matte Black
Brushed Silver Multi-Spoke Turbine Forged Wheels
Monoblock · Bright Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Hamann BMW 5-Series F10 M-Technik ships from the factory on a 5x120 bolt pattern with a 72.6mm center bore and a 19x8.5J ET33 wheel. Our flush reference for the Hamann BMW 5-Series F10 M-Technik is 20x9J ET25.; our maximum aggressive reference is 21x9.5J ET25. — beyond that, expect clearance issues against the fender liner without further modification.
Hamann BMW 5-Series F10 M-Technik OE Wheel Specs
The Hamann BMW 5-Series F10 M-Technik ships from the factory on 5x120 bolt pattern wheels with a 72.6mm center bore. The stock wheel size is 19x8.5J ET33, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Hamann BMW 5-Series F10 M-Technik (2011) we drill the 5x120 pattern and cut the centre bore to 72.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 19x8.5J | ET33 | 6.05 in (154 mm) | — | — |
| Flush | 20x9J | ET25 | 5.98 in (152 mm) | −2 mm | +14 mm |
| Maximum | 21x9.5J | ET25 | 6.23 in (158 mm) | +5 mm | +21 mm |
Vehicles With the Same Hub as the Hamann BMW 5-Series F10 M-Technik (5x120, 72.6 mm Bore)
In our database, 338 other vehicle entries from 10 makes use exactly the same 5x120 bolt pattern and 72.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x120 is used by 10.3% of the vehicle pages in our English fitment guide (670 of 6,503); 50.6% of those also use a 72.6 mm center bore.
Hub-Centric Rings for a 72.6 mm Center Bore
A wheel with a center bore larger than 72.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 73.1 mm | 73.1 → 72.6 mm |
| 74.1 mm | 74.1 → 72.6 mm |
| 76.1 mm | 76.1 → 72.6 mm |
| 78.1 mm | 78.1 → 72.6 mm |
ANKUSI forged wheels are bored to exactly 72.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Hamann BMW 5-Series F10 M-Technik use?
The 2011 Hamann BMW 5-Series F10 M-Technik uses a 5x120 bolt pattern.
How many lug bolts does the Hamann BMW 5-Series F10 M-Technik use?
The Hamann BMW 5-Series F10 M-Technik uses a 5-lug bolt pattern (5x120), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Hamann BMW 5-Series F10 M-Technik?
The Hamann BMW 5-Series F10 M-Technik's center bore is 72.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Hamann BMW 5-Series F10 M-Technik?
Factory wheels on the Hamann BMW 5-Series F10 M-Technik are 19x8.5J ET33.
What does a flush wheel fitment look like on the Hamann BMW 5-Series F10 M-Technik?
For a flush look with minimal to no rubbing, we recommend 20x9J at ET25 offset as a starting point on a stock or mildly lowered Hamann BMW 5-Series F10 M-Technik.
Do I need wheel spacers for my Hamann BMW 5-Series F10 M-Technik?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Hamann BMW 5-Series F10 M-Technik?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.98" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Hamann BMW 5-Series F10 M-Technik?
The Hamann BMW 5-Series F10 M-Technik runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x8.5 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.