Belak-Style Gloss Black Machined 12-Spoke Red-Ring Beadlock Forged Drag Racing Wheels
Drag Racing · Custom Finish
2013 Ford Taurus Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ford Taurus wheels? This page gives the 2013 Ford Taurus bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Ford Taurus rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2013 Ford Taurus uses a 5x114.3 bolt pattern with a 63.4 mm centre bore and M12x1.5 lug nuts. Factory wheels: 18x8.0J, front and rear. For aftermarket wheels, 19x8.5J ET40 sits flush and 20x9.0J ET38 is the most aggressive fit.
Forged wheels for the 2013 Ford Taurus — drilled 5x114.3 with a 63.4 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Ford Taurus (2013): 5x114.3 bolt pattern, 63.4mm center bore. Factory wheels: 18x8.0J F/R. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore63.4mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2013
CategorySedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 25, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8.0J F/R |
| Flush Fitment | 19x8.5J at ET40 offset |
| Maximum Aggressive | 20x9.0J at ET38 offset |
Forged Wheel Designs for the Ford Taurus
Every design below is forged to order, so it can be machined to the Ford Taurus's 5x114.3 bolt pattern and 63.4 mm center bore, with the width and offset calculated for your setup.
Belak-Style Gloss Black / Purple Mesh Beadlock Forged Drag Racing Wheels
Drag Racing · Gloss Black / Purple
Ford Mustang OEM-Style Transparent Black Brushed 5 Y-Spoke Concave Forged Wheels
Replica · Transparent Black
Ford Mustang OEM-Style Custom Finish 2-Piece Forged Wheels
2-Piece · Custom Finish
A Forged-Style Polished / Gunmetal Mesh 2-Piece Riveted Deep Lip Forged Wheels
2-Piece · Polished / Gunmetal
Weld Racing-Style Gloss Black 5-Star Beadlock Forged Drag Racing Wheels
Drag Racing · Gloss Black / Machined
Belak-Style Gloss Black Milled Mesh Double-Row Beadlock Forged Drag Racing Wheels
Drag Racing · Gloss Black
Vossen Gloss Black / Gunmetal Multi-Spoke Forged Wheels
Replica · Gloss Black / Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Taurus's factory wheel is sized for fuel economy and everyday ride comfort on a full-size sedan platform, so the case for forging is the same one that applies across this whole class of car: hold the factory load rating at a lighter weight, and the ride and steering both benefit without changing the car's basic character.
The Taurus uses a 5x114.3 bolt pattern, 63.4mm center bore, and an 18x8.0J wheel front and rear from the factory. Our Flush Fitment reference is a 19x8.5J at ET40, the recommended starting point on a stock or mildly lowered Taurus. Our Maximum Aggressive reference is a 20x9.0J at ET38 — past that, expect rubbing under compression without fender rolling or camber correction.
Ford Taurus OE Wheel Specs
The 2013 Ford Taurus (Sedan) uses a 5*108 bolt pattern with a 63.4mm center bore. Factory wheels are 18x8.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ford Taurus (2013) we drill the 5x114.3 pattern and cut the centre bore to 63.4mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- Flush: 19x8.5J ET40 → ~6.32″ backspacing
- Max: 20x9J ET38 → ~6.5″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ford spec, or want a wheel built to a custom offset for your Ford Taurus? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Ford Taurus (5x114.3, 63.4 mm Bore)
In our database, 24 other vehicle entries from 4 makes use exactly the same 5x114.3 bolt pattern and 63.4 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 1.9% of those also use a 63.4 mm center bore.
Hub-Centric Rings for a 63.4 mm Center Bore
A wheel with a center bore larger than 63.4 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 64.1 mm | 64.1 → 63.4 mm |
| 65.1 mm | 65.1 → 63.4 mm |
| 66.1 mm | 66.1 → 63.4 mm |
| 66.6 mm | 66.6 → 63.4 mm |
| 73.1 mm | 73.1 → 63.4 mm |
ANKUSI forged wheels are bored to exactly 63.4 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford Taurus use?
The 2013 Ford Taurus uses a 5x114.3 bolt pattern.
How many lug bolts does the Ford Taurus use?
The Ford Taurus uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ford Taurus?
The Ford Taurus's center bore is 63.4mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ford Taurus?
Factory wheels on the Ford Taurus are 18x8.0J F/R.
What is the biggest wheel size I can fit on my Ford Taurus without rubbing?
The most aggressive fitment we recommend without fender work is 20x9.0J at ET38 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ford Taurus?
For a flush look with minimal to no rubbing, we recommend 19x8.5J at ET40 offset as a starting point on a stock or mildly lowered Ford Taurus.
Do I need wheel spacers for my Ford Taurus?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ford Taurus?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.32" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ford Taurus?
The Ford Taurus runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 136 Nm (100 ft-lb). Covers most Ford passenger cars and crossovers (Fusion, Focus, Escape and similar) on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x8 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.