Rays-Style Gunmetal 10 Y-Mesh Forged Wheels
Nissan 370Z / Toyota GR86 Fitment · 5-Lug
2006 FPV BF MkII GT Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting FPV BF MkII GT wheels? This page gives the 2006 FPV BF MkII GT bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged FPV BF MkII GT rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
FPV BF MkII GT (2006): 5x114.3 bolt pattern, 70.5mm center bore. Factory wheels: 19x8.0J F/R. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore70.5mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2006
CategoryMuscle Car
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x8.0J F/R |
| Flush Fitment | 19x8.5J at ET30 offset |
| Maximum Aggressive | 19x9.5J at ET25 offset |
Forged wheels for the FPV BF MkII GTMachined to the 5x114.3 bolt pattern and 70.5 mm bore · 14–24 inch · offset calculated for your car · 3D drawing before production
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The FPV BF MkII GT runs a 5x114.3 bolt pattern, 70.5mm center bore, and a 19x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.5J ET30, which tucks the tire under the fender lip on a stock-height FPV BF MkII GT. Our Maximum Aggressive reference is 19x9.5J ET25 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
FPV BF MkII GT OE Wheel Specs
The 2006 FPV BF MkII GT (Muscle Car) uses a 5x114.3 bolt pattern with a 70.5mm center bore. Factory wheels are 19x8.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday drivability
- A commonly used size for this vehicle class, supporting parts and tire availability
- Maintains clearance for the factory suspension and brake components
- Provides stable, predictable handling across normal driving conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the FPV BF MkII GT (2006) we drill the 5x114.3 pattern and cut the centre bore to 70.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look with minimal rubbing, F/R 19x8.5J ET30 is the recommended starting point on a stock or mildly lowered FPV BF MkII GT.
Maximum Aggressive Fitment
F/R 19x9.5J ET25 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style 19x8.0J ET36
Recommended setup: 19x8.0J ET36 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,200-1,500 (wheels + tires + install)
B Comfortable Upgrade 19x8.5J ET33
Recommended setup: 19x8.5J ET33 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 19x8.5J ET30
Recommended setup: 19x8.5J ET30 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 19x9.0J ET28
Recommended setup: 19x9.0J ET28 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 19x9.5J ET25
Recommended setup: 19x9.5J ET25 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 19x8.0J ET36 | 19x8.5J ET33 | 19x8.5J ET30 | 19x9.0J ET28 | 19x9.5J ET25 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $1,200-1,500 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 19x8.0J ET36
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 19x8.5J ET30
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 19x9.5J ET25
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
1
What's your primary use? Daily commuting → Tier A/B. Weekend street driving → Tier B/C. Show or occasional track use → Tier D/E.
2
What's your budget? Under $800 → Tier A. $800-3,400 → Tier B/C. $3,400+ → Tier D/E.
3
How much does fuel economy matter? Very important → Tier A. Somewhat important → Tier B/C. Not a priority → Tier D/E.
4
Still unsure? Tier C (Balanced / Flush Fit) is the default choice for most FPV BF MkII GT owners.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 19x8.0J ET36.5 → ~5.94″ backspacing
- Flush: 19x8.5J ET30 → ~5.93″ backspacing
- Max: 19x9.5J ET25 → ~6.23″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact FPV spec, or want a wheel built to a custom offset for your FPV BF MkII GT? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Custom Forged Wheels for the FPV BF MkII GT (2006)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x114.3 pattern and the 70.5mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose — most FPV orders on this platform land somewhere between the 19x8.5J ET30 flush setup and the 19x9.5J ET25 aggressive setup referenced above.
Designs we already tool for the 5x114.3 pattern — each one is re-cut to your sizes and offsets:
Vossen Gray Directional Multi-Spoke Forged Wheels – Tesla Model Y / Ford Mustang Fitment (5-Lug)
Ford Mustang / Chevrolet Corvette Forged Wheels – Gloss White Slotted Dish
Alpine OEM-Style Hyper Silver 5 Y-Spoke Forged Wheels – Alpine A290 Fitment (5-Lug)
Vossen HF-5-Style Bronze 5 Y-Spoke Concave Forged Wheels - Tesla Model 3 / Tesla Model Y Fitment (5-Lug)Frequently Asked Questions
What bolt pattern (PCD) does the FPV BF MkII GT use?
The 2006 FPV BF MkII GT uses a 5x114.3 bolt pattern.
How many lug bolts does the FPV BF MkII GT use?
The FPV BF MkII GT uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the FPV BF MkII GT?
The FPV BF MkII GT's center bore is 70.5mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the FPV BF MkII GT?
Factory wheels on the FPV BF MkII GT are 19x8.0J F/R.
What is the biggest wheel size I can fit on my FPV BF MkII GT without rubbing?
The most aggressive fitment we recommend without fender work is 19x9.5J at ET25 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the FPV BF MkII GT?
For a flush look with minimal to no rubbing, we recommend 19x8.5J at ET30 offset as a starting point on a stock or mildly lowered FPV BF MkII GT.
Do I need wheel spacers for my FPV BF MkII GT?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my FPV BF MkII GT?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.93" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my FPV BF MkII GT?
The FPV BF MkII GT runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Vehicles With the Same Hub as the FPV BF MkII GT (5x114.3, 70.5 mm Bore)
In our database, 155 other vehicle entries from 6 makes use exactly the same 5x114.3 bolt pattern and 70.5 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.1% of the vehicle entries in our database (1,284 of 6,396); 12.1% of those also use a 70.5 mm center bore.
Hub-Centric Rings for a 70.5 mm Center Bore
A wheel with a center bore larger than 70.5 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 71.6 mm | 71.6 → 70.5 mm |
| 72.6 mm | 72.6 → 70.5 mm |
| 73.1 mm | 73.1 → 70.5 mm |
| 74.1 mm | 74.1 → 70.5 mm |
ANKUSI forged wheels are bored to exactly 70.5 mm for this vehicle, so no ring is needed.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x8 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Forged Wheel Designs for the FPV BF MkII GT
Every design below is forged to order, so it can be machined to the FPV BF MkII GT's 5x114.3 bolt pattern and 70.5 mm center bore, with the width and offset calculated for your setup.
Lexus LS / LC Forged Wheels
Matte Silver 5-Spoke Machined Face
Alpine OEM-Style Hyper Silver 5 Y-Spoke Forged Wheels
Alpine A290 Fitment · 5-Lug
Vossen HF-5-Style Bronze 5 Y-Spoke Concave Forged Wheels - Tesla Model 3 / Tesla Model Y Fitment (5-Lug)
Vossen-Style forged wheels featuring the HF-5-style bronze 5 Y-spoke concave design, forged to order at ANKUSI's Guangzhou plant. Bolt pattern, centre bore, diameter, width and offset are machined for your exact vehicle — this listing covers 5-lug applications.
Honda Civic / Accord Forged Wheels
Gunmetal 5 Y-Spoke Concave · 5-Lug
Ferrari 488 / F8 Forged Wheels
Gloss Black Mesh Carbon Fibre
Rays-Style Silver 6-Spoke Forged Wheels
Toyota GR86 / Subaru WRX Fitment · 5-Lug
Ferrari 488 / F8 Forged Wheels
Matte Silver
Bolt pattern and center bore on this page were cross-checked against at least two independent sources before publication. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.