Gunmetal Petal Machined Face Forged Wheels
Monoblock · Gunmetal
2027 Geely Galaxy TT Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Geely Galaxy TT wheels? This page gives the 2027 Geely Galaxy TT bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Geely Galaxy TT rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2027 Geely Galaxy TT uses a 5x114.3 bolt pattern with a 63.4 mm centre bore and M12x1.5 lug nuts. Factory wheels: 19x8J ET45. For aftermarket wheels, 20x9J ET35 sits flush.
Forged wheels for the 2027 Geely Galaxy TT — drilled 5x114.3 with a 63.4 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Geely Galaxy TT (2027): 5x114.3 bolt pattern, 63.4mm center bore, OE 19x8J ET45. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore63.4mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2027
Category5-Lug Large Sedan/SUV
Data check: we have not yet been able to confirm this vehicle's bolt pattern and centre bore with an independent source. Measure your hub or send us a photo before ordering. Contact us
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x8J ET45 |
| Flush Fitment | 20x9J at ET35 offset |
Forged Wheel Designs for the Geely Galaxy TT
Every design below is forged to order, so it can be machined to the Geely Galaxy TT's 5x114.3 bolt pattern and 63.4 mm center bore, with the width and offset calculated for your setup.
Geely Xingrui L Plus Forged Wheels
Monoblock
Vossen LC3-01T-Style Brushed Silver 5-Spoke Forged Wheels
Replica · Brushed Silver
BBS-Style Hyper Silver 5 Split-Spoke Forged Wheels
Replica · Bright Silver
Geely OEM-Style Gloss Black 5 Y-Split-Spoke Forged Wheels
Monoblock · Gloss Black
Geely OEM-Style Matte Black 10 Y-Spoke Forged Wheels
Monoblock · Matte Black
Chrome 10 Y-Spoke 2-Piece Riveted Forged Wheels
2-Piece · Chrome
OZ Racing-Style Polished Turbofan Dish Riveted Lip Forged Wheels
2-Piece · Polished
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Geely Galaxy TT ships from the factory on a 5x114.3 bolt pattern with a 63.4mm center bore and a 19x8J ET45 wheel. Our flush reference for the Geely Galaxy TT is 20x9J ET35.; our maximum aggressive reference is 21x9.5J ET32. — beyond that, expect clearance issues against the fender liner without further modification.
Geely Galaxy TT OE Wheel Specs
The Geely Galaxy TT ships from the factory on 5x114.3 bolt pattern wheels with a 63.4mm center bore. The stock wheel size is 19x8J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Geely Galaxy TT (2027) we drill the 5x114.3 pattern and cut the centre bore to 63.4mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 19x8J | ET45 | 6.27 in (159 mm) | — | — |
| Flush | 20x9J | ET35 | 6.38 in (162 mm) | +3 mm | +23 mm |
| Maximum | 21x9.5J | ET32 | 6.51 in (165 mm) | +6 mm | +32 mm |
Vehicles With the Same Hub as the Geely Galaxy TT (5x114.3, 63.4 mm Bore)
In our database, 24 other vehicle entries from 4 makes use exactly the same 5x114.3 bolt pattern and 63.4 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 1.9% of those also use a 63.4 mm center bore.
Hub-Centric Rings for a 63.4 mm Center Bore
A wheel with a center bore larger than 63.4 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 64.1 mm | 64.1 → 63.4 mm |
| 65.1 mm | 65.1 → 63.4 mm |
| 66.1 mm | 66.1 → 63.4 mm |
| 66.6 mm | 66.6 → 63.4 mm |
| 73.1 mm | 73.1 → 63.4 mm |
ANKUSI forged wheels are bored to exactly 63.4 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Geely Galaxy TT use?
The 2027 Geely Galaxy TT uses a 5x114.3 bolt pattern.
How many lug bolts does the Geely Galaxy TT use?
The Geely Galaxy TT uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Geely Galaxy TT?
The Geely Galaxy TT's center bore is 63.4mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Geely Galaxy TT?
Factory wheels on the Geely Galaxy TT are 19x8J ET45.
What does a flush wheel fitment look like on the Geely Galaxy TT?
For a flush look with minimal to no rubbing, we recommend 20x9J at ET35 offset as a starting point on a stock or mildly lowered Geely Galaxy TT.
Do I need wheel spacers for my Geely Galaxy TT?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Geely Galaxy TT?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.38" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Geely Galaxy TT?
The Geely Galaxy TT runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x8 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.