Porsche 911 / M3 Forged Wheels
Gloss White 5-Spoke · 5-Lug
2013 Fisker Surf Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Fisker Surf wheels? This page gives the 2013 Fisker Surf bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Fisker Surf rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Fisker Surf (2013): 5x130 bolt pattern, 66.9mm center bore. Factory wheels: F: 22x8.5J R: 22x9.5J. Reference fitment ranges.
Bolt Pattern5x130
Center Bore66.9mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2013
CategoryWagon
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 22x8.5J R: 22x9.5J |
| Flush Fitment | F 22x9.5J ET35 / R 22x10.5J ET30 |
| Maximum Aggressive | F 22x10.0J ET30 / R 22x11.0J ET25 |
Forged wheels for the Fisker SurfMachined to the 5x130 bolt pattern and 66.9 mm bore · 14–24 inch · offset calculated for your car · 3D drawing before production
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A wagon carries wagon-specific weight distribution — more mass over the rear axle when loaded — so wheel strength at the rear corners matters as much as the front. Forging lets us match the factory's strength target on both ends while keeping rotational mass down, which keeps the ride composed whether the cargo area is empty or full.
The Fisker Surf runs a 5x130 bolt pattern, 66.9mm center bore, and a F: 22x8.5J wheel from the factory. Our Flush Fitment reference is F 22x9.5J ET35 / R 22x10.5J ET30, which tucks the tire under the fender lip on a stock-height Fisker Surf. Our Maximum Aggressive reference is F 22x10.0J ET30 / R 22x11.0J ET25 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Fisker Surf OE Wheel Specs
The 2013 Fisker Surf (Wagon) uses a 5x130 bolt pattern with a 66.9mm center bore. Factory wheels are F: 22x8.5J R: 22x9.5J.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Fisker Surf (2013) we drill the 5x130 pattern and cut the centre bore to 66.9mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look with minimal rubbing, F 22x9.5J ET35 / R 22x10.5J ET30 is the recommended starting point on a stock or mildly lowered Fisker Surf.
Maximum Aggressive Fitment
F 22x10.0J ET30 / R 22x11.0J ET25 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style F 22x8.5J ET42 / R 22x9.5J ET40
Recommended setup: F 22x8.5J ET42 / R 22x9.5J ET40 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,200-1,500 (wheels + tires + install)
B Comfortable Upgrade F 22x9.0J ET39 / R 22x10.0J ET35
Recommended setup: F 22x9.0J ET39 / R 22x10.0J ET35 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit F 22x9.5J ET35 / R 22x10.5J ET30
Recommended setup: F 22x9.5J ET35 / R 22x10.5J ET30 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive F 22x10.0J ET33 / R 22x11.0J ET28
Recommended setup: F 22x10.0J ET33 / R 22x11.0J ET28 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive F 22x10.0J ET30 / R 22x11.0J ET25
Recommended setup: F 22x10.0J ET30 / R 22x11.0J ET25 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | F 22x8.5J ET42 / R 22x9.5J ET40 | F 22x9.0J ET39 / R 22x10.0J ET35 | F 22x9.5J ET35 / R 22x10.5J ET30 | F 22x10.0J ET33 / R 22x11.0J ET28 | F 22x10.0J ET30 / R 22x11.0J ET25 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $1,200-1,500 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: F 22x8.5J ET42 / R 22x9.5J ET40
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: F 22x9.5J ET35 / R 22x10.5J ET30
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: F 22x10.0J ET30 / R 22x11.0J ET25
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
1
What's your primary use? Daily commuting → Tier A/B. Weekend street driving → Tier B/C. Show or occasional track use → Tier D/E.
2
What's your budget? Under $800 → Tier A. $800-3,400 → Tier B/C. $3,400+ → Tier D/E.
3
How much does fuel economy matter? Very important → Tier A. Somewhat important → Tier B/C. Not a priority → Tier D/E.
4
Still unsure? Tier C (Balanced / Flush Fit) is the default choice for most Fisker Surf owners.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 22x8.5J ET42.6 → ~6.43″ F backspacing, R 22x9.5J ET40.7 → ~6.85″ R backspacing
- Flush: F 22x9.5J ET35 → ~6.63″ F backspacing, R 22x10.5J ET30 → ~6.93″ R backspacing
- Max: F 22x10.0J ET30 → ~6.68″ F backspacing, R 22x11.0J ET25 → ~6.98″ R backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Fisker spec, or want a wheel built to a custom offset for your Fisker Surf? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Custom Forged Wheels for the Fisker Surf (2013)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x130 pattern and the 66.9mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose.
Designs we already tool for the 5x130 pattern — each one is re-cut to your sizes and offsets:
ABL Studios-Style Gloss Black Multi-Spoke Double Ring Floating Cap Forged Wheels – Bentley Continental GT / Rolls-Royce Ghost Fitment (5-Lug)
Porsche 911 / BMW M3 Forged Wheels – Matte Gold 8-Spoke Deep Lip
Bugatti OEM-Style Polished Directional Machined-Face Forged Wheels – Bugatti Chiron Fitment (5-Lug)
Porsche 911 / Cayenne Forged Wheels – Black / PolishedFrequently Asked Questions
What bolt pattern (PCD) does the Fisker Surf use?
The 2013 Fisker Surf uses a 5x130 bolt pattern.
How many lug bolts does the Fisker Surf use?
The Fisker Surf uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Fisker Surf?
The Fisker Surf's center bore is 66.9mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Fisker Surf?
Factory wheels on the Fisker Surf are F: 22x8.5J R: 22x9.5J.
What is the biggest wheel size I can fit on my Fisker Surf without rubbing?
The most aggressive fitment we recommend without fender work is F 22x10.0J ET30 / R 22x11.0J ET25. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Fisker Surf?
For a flush look with minimal to no rubbing, we recommend F 22x9.5J ET35 / R 22x10.5J ET30 as a starting point on a stock or mildly lowered Fisker Surf.
Do I need wheel spacers for my Fisker Surf?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Fisker Surf?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.63" backspacing up front and 6.93" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Fisker Surf?
Yes — the Fisker Surf's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Vehicles With the Same Hub as the Fisker Surf (5x130, 66.9 mm Bore)
In our database, 1 other Fisker entries use exactly the same 5x130 bolt pattern and 66.9 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x130 is used by 5.8% of the vehicle entries in our database (372 of 6,396); 0.5% of those also use a 66.9 mm center bore.
Hub-Centric Rings for a 66.9 mm Center Bore
A wheel with a center bore larger than 66.9 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 67.1 mm | 67.1 → 66.9 mm |
| 70.1 mm | 70.1 → 66.9 mm |
| 70.5 mm | 70.5 → 66.9 mm |
| 71.6 mm | 71.6 → 66.9 mm |
| 73.1 mm | 73.1 → 66.9 mm |
ANKUSI forged wheels are bored to exactly 66.9 mm for this vehicle, so no ring is needed.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 22x8.5 wheels · 22 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Forged Wheel Designs for the Fisker Surf
Every design below is forged to order, so it can be machined to the Fisker Surf's 5x130 bolt pattern and 66.9 mm center bore, with the width and offset calculated for your setup.
BBS-Style Gunmetal 5 Y-Spoke Forged Wheels
Porsche 911 / M3 Fitment · 5-Lug
BBS CI-R-Style High-Gloss Silver 10-Spoke Y-Design Forged Wheels
BMW M3 CS Handschalter Fitment · 19-21in, 5x112
Porsche 911 / Panamera Forged Wheels
Gloss Black / Gunmetal / Gray 5 Y-Spoke
Rotiform-Style Gloss Black 5-Spoke Forged Wheels
Porsche 911 / M3 Fitment · 5-Lug
Patsha Matte Black 5 Y-Spoke Forged Wheels
Porsche 911 / M3 Fitment · 5-Lug
HRE-Style Hyper Silver 10 Y-Spoke Mesh Polished Lip Forged Wheels
Porsche 911 / M3 Fitment · 5-Lug
Porsche 911 / M3 Forged Wheels
Matte Black 5 Y-Spoke Machined Lip · 5-Lug
Bolt pattern and center bore on this page were cross-checked against at least two independent sources before publication. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.