Brabus-Style Gloss Black Carbon-Ring 10-Spoke Red Pinstripe Forged Wheels
Monoblock · Gloss Black
2003 Brabus Mercedes-Benz G V12 Biturbo Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Brabus Mercedes-Benz G V12 Biturbo wheels? This page gives the 2003 Brabus Mercedes-Benz G V12 Biturbo bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Brabus Mercedes-Benz G V12 Biturbo rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2003 Brabus Mercedes-Benz G V12 Biturbo uses a 5x130 bolt pattern with a 84.1 mm centre bore and M14x1.5 lug bolts. Factory wheels: 22x10.0J, front and rear. For aftermarket wheels, 23x10.5J ET30 sits flush and 23x11.0J ET25 is the most aggressive fit.
Forged wheels for the 2003 Brabus Mercedes-Benz G V12 Biturbo — drilled 5x130 with a 84.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Brabus Mercedes-Benz G V12 Biturbo (2003): 5x130 bolt pattern, 84.1mm center bore. Factory wheels: 22x10.0J F/R. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore84.1mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2003
CategorySUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 22x10.0J F/R |
| Flush Fitment | 23x10.5J at ET30 offset |
| Maximum Aggressive | 23x11.0J at ET25 offset |
Forged Wheel Designs for the Brabus Mercedes-Benz G V12 Biturbo
Every design below is forged to order, so it can be machined to the Brabus Mercedes-Benz G V12 Biturbo's 5x130 bolt pattern and 84.1 mm center bore, with the width and offset calculated for your setup.
HRE 522M-Style White Directional Milled Forged Wheels
Replica · White
Wheelforce-Style Gold Side-Milled Forged Wheels
Replica · Gold
Gloss Black / Gunmetal Custom Forged Wheels
Monoblock · Gloss Black / Gunmetal
APEX-Style Gold Mesh Deep Dish Forged Wheels
Deep Dish · Gold
OZ Racing-Style Matte Black 15-Spoke Forged Wheels
Monoblock · Matte Black
HRE Performance 522M-Style Brushed Silver Directional Milled Forged Wheels
Replica · Brushed Silver
Gloss Black 5-Spoke Polished Lip Forged Wheels
Monoblock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Because an SUV's center of gravity is already higher than a sedan's, anything added at the corners — including wheel weight — has an outsized effect on handling balance. A forged wheel lets us hit the visual stance owners want without adding the rotational mass a cast wheel of the same strength would carry.
The Brabus Mercedes-Benz G V12 Biturbo runs a 5x130 bolt pattern, 84.1mm center bore, and a 22x10.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 23x10.5J ET30, which tucks the tire under the fender lip on a stock-height Brabus Mercedes-Benz G V12 Biturbo. Our Maximum Aggressive reference is 23x11.0J ET25 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Brabus Mercedes-Benz G V12 Biturbo OE Wheel Specs
The 2003 Brabus Mercedes-Benz G V12 Biturbo (SUV) uses a 5x130 bolt pattern with a 84.1mm center bore. Factory wheels are 22x10.0J F/R.
Why the factory spec works for most owners:
- Preserves the factory-tuned ride and steering feel
- A mainstream size for this segment, keeping tire choice wide and prices reasonable
- Leaves full clearance for the stock brakes and suspension hardware
- Keeps handling predictable and consistent in everyday conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Brabus Mercedes-Benz G V12 Biturbo (2003) we drill the 5x130 pattern and cut the centre bore to 84.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 22x10.0J ET35 → ~6.88″ backspacing
- Flush: 23x10.5J ET30 → ~6.93″ backspacing
- Max: 23x11.0J ET25 → ~6.98″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Brabus spec, or want a wheel built to a custom offset for your Brabus Mercedes-Benz G V12 Biturbo? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Brabus Mercedes-Benz G V12 Biturbo (5x130, 84.1 mm Bore)
In our database, 34 other vehicle entries from 3 makes use exactly the same 5x130 bolt pattern and 84.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x130 is used by 5.8% of the vehicle pages in our English fitment guide (375 of 6,503); 9.3% of those also use a 84.1 mm center bore.
Hub-Centric Rings for a 84.1 mm Center Bore
A wheel with a center bore larger than 84.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 93.1 mm | 93.1 → 84.1 mm |
| 100.1 mm | 100.1 → 84.1 mm |
| 106.1 mm | 106.1 → 84.1 mm |
| 108.1 mm | 108.1 → 84.1 mm |
ANKUSI forged wheels are bored to exactly 84.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Brabus Mercedes-Benz G V12 Biturbo use?
The 2003 Brabus Mercedes-Benz G V12 Biturbo uses a 5x130 bolt pattern.
How many lug bolts does the Brabus Mercedes-Benz G V12 Biturbo use?
The Brabus Mercedes-Benz G V12 Biturbo uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Brabus Mercedes-Benz G V12 Biturbo?
The Brabus Mercedes-Benz G V12 Biturbo's center bore is 84.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Brabus Mercedes-Benz G V12 Biturbo?
Factory wheels on the Brabus Mercedes-Benz G V12 Biturbo are 22x10.0J F/R.
What is the biggest wheel size I can fit on my Brabus Mercedes-Benz G V12 Biturbo without rubbing?
The most aggressive fitment we recommend without fender work is 23x11.0J at ET25 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Brabus Mercedes-Benz G V12 Biturbo?
For a flush look with minimal to no rubbing, we recommend 23x10.5J at ET30 offset as a starting point on a stock or mildly lowered Brabus Mercedes-Benz G V12 Biturbo.
Do I need wheel spacers for my Brabus Mercedes-Benz G V12 Biturbo?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Brabus Mercedes-Benz G V12 Biturbo?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.93" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Brabus Mercedes-Benz G V12 Biturbo?
The Brabus Mercedes-Benz G V12 Biturbo runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 22x10 wheels · 22 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.