Gloss Black Directional Milled Forged Wheels
Monoblock · Gloss Black
2026 DS No4 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting DS No4 wheels? This page gives the 2026 DS No4 bolt pattern (5x108), centre bore, factory rim size and the offset range for aftermarket and forged DS No4 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2026 DS No4 uses a 5x108 bolt pattern with a 65.1 mm centre bore and M12x1.25 lug bolts. Factory wheels: 19x7.5J, front and rear. For aftermarket wheels, 20x8.5J ET35 sits flush and 20x9.0J ET30 is the most aggressive fit.
Forged wheels for the 2026 DS No4 — drilled 5x108 with a 65.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
DS No4 (2026): 5x108 bolt pattern, 65.1mm center bore. Factory wheels: 19x7.5J F/R. Reference fitment ranges.
Bolt Pattern5x108
Wheel Bolt/NutM12x1.25 Bolt
Center Bore65.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2026
CategoryHatchback
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x7.5J F/R |
| Flush Fitment | 20x8.5J at ET35 offset |
| Maximum Aggressive | 20x9.0J at ET30 offset |
Forged Wheel Designs for the DS No4
Every design below is forged to order, so it can be machined to the DS No4's 5x108 bolt pattern and 65.1 mm center bore, with the width and offset calculated for your setup.
Gloss Black Custom Forged Wheels
Off-Road Beadlock · Gloss Black
WF Side-Milled Brushed Silver 5 Y-Spoke Forged Wheels
Replica · Side-milled Brushed Silver
APEX ARC-8-Style Bright Silver 8 Y-Spoke Mesh Forged Wheels
Replica · Bright Silver
Bronze Gold 5-Spoke Directional Forged Wheels
Monoblock · Bronze Gold
Lynk & Co OEM-Style Brushed Silver Directional Forged Wheels
Monoblock · Brushed Silver
Gunmetal Machined Face Forged Wheels
Monoblock · Gunmetal
Gunmetal Mesh Forged Wheels
Monoblock · Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a compact performance platform, every pound of rotational mass fights the car's natural agility. A forged wheel keeps strength at the factory-rated level while cutting that rotational weight, which is where the driving-feel improvement actually comes from.
The DS No4 runs a 5x108 bolt pattern, 65.1mm center bore, and a 19x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x8.5J ET35, which tucks the tire under the fender lip on a stock-height DS No4. Our Maximum Aggressive reference is 20x9.0J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
DS No4 OE Wheel Specs
The 2026 DS No4 (Hatchback) uses a 5x108 bolt pattern with a 65.1mm center bore. Factory wheels are 19x7.5J F/R.
Why the factory spec works for most owners:
- Preserves the factory-tuned ride and steering feel
- A mainstream size for this segment, keeping tire choice wide and prices reasonable
- Leaves full clearance for the stock brakes and suspension hardware
- Keeps handling predictable and consistent in everyday conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the DS No4 (2026) we drill the 5x108 pattern and cut the centre bore to 65.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 19x7.5J ET44 → ~5.98″ backspacing
- Flush: 20x8.5J ET35 → ~6.13″ backspacing
- Max: 20x9.0J ET30 → ~6.18″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact DS spec, or want a wheel built to a custom offset for your DS No4? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the DS No4 (5x108, 65.1 mm Bore)
In our database, 113 other vehicle entries from 15 makes use exactly the same 5x108 bolt pattern and 65.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x108 is used by 7.7% of the vehicle pages in our English fitment guide (499 of 6,503); 22.8% of those also use a 65.1 mm center bore.
Hub-Centric Rings for a 65.1 mm Center Bore
A wheel with a center bore larger than 65.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 66.1 mm | 66.1 → 65.1 mm |
| 66.6 mm | 66.6 → 65.1 mm |
| 67.1 mm | 67.1 → 65.1 mm |
| 70.1 mm | 70.1 → 65.1 mm |
| 73.1 mm | 73.1 → 65.1 mm |
ANKUSI forged wheels are bored to exactly 65.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the DS No4 use?
The 2026 DS No4 uses a 5x108 bolt pattern.
How many lug bolts does the DS No4 use?
The DS No4 uses a 5-lug bolt pattern (5x108), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the DS No4?
The DS No4's center bore is 65.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the DS No4?
Factory wheels on the DS No4 are 19x7.5J F/R.
What is the biggest wheel size I can fit on my DS No4 without rubbing?
The most aggressive fitment we recommend without fender work is 20x9.0J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the DS No4?
For a flush look with minimal to no rubbing, we recommend 20x8.5J at ET35 offset as a starting point on a stock or mildly lowered DS No4.
Do I need wheel spacers for my DS No4?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my DS No4?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.13" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my DS No4?
The DS No4 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x7.5 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.