Matte Silver 5-Spoke Forged Wheels
Monoblock · Matte Silver
2019 DS 7 Crossback E-Tense 4x4 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting DS 7 Crossback E-Tense 4x4 wheels? This page gives the 2019 DS 7 Crossback E-Tense 4x4 bolt pattern (5x108), centre bore, factory rim size and the offset range for aftermarket and forged DS 7 Crossback E-Tense 4x4 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2019 DS 7 Crossback E-Tense 4x4 uses a 5x108 bolt pattern with a 65.1 mm centre bore and M12x1.25 lug bolts. Factory wheels: 20x8.0J, front and rear. For aftermarket wheels, 21x9.0J ET35 sits flush and 21x9.5J ET30 is the most aggressive fit.
Forged wheels for the 2019 DS 7 Crossback E-Tense 4x4 — drilled 5x108 with a 65.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
DS 7 Crossback E-Tense 4x4 (2019): 5x108 bolt pattern, 65.1mm center bore. Factory wheels: 20x8.0J F/R. Reference fitment ranges.
Bolt Pattern5x108
Wheel Bolt/NutM12x1.25 Bolt
Center Bore65.1mm
Wheel Load Rating1035–1438 kg/wheel (SUV segment reference)
Year2019
CategoryPHEV SUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 20x8.0J F/R |
| Flush Fitment | 21x9.0J at ET35 offset |
| Maximum Aggressive | 21x9.5J at ET30 offset |
Forged Wheel Designs for the DS 7 Crossback E-Tense 4x4
Every design below is forged to order, so it can be machined to the DS 7 Crossback E-Tense 4x4's 5x108 bolt pattern and 65.1 mm center bore, with the width and offset calculated for your setup.
Lynk & Co OEM-Style Gloss Black Multi-Spoke Forged Wheels
Monoblock · Gloss Black
Metallic Gray 5-Spoke Forged Wheels
Monoblock · Metallic Gray
APEX-Style Chrome 5 Split-Spoke Forged Wheels
Replica · Chrome Silver
Satin Black 10 Y-Spoke Forged Wheels
Monoblock · Satin Black
Matte Silver Full-Face Deep Lip Forged Wheels
Off-Road · Matte Silver
Gloss Black 5 Y-Spoke Forged Wheels
Monoblock · Gloss Black
Silver Deep Lip Full-Face Riveted Forged Wheels
Off-Road · Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Because an SUV's center of gravity is already higher than a sedan's, anything added at the corners — including wheel weight — has an outsized effect on handling balance. A forged wheel lets us hit the visual stance owners want without adding the rotational mass a cast wheel of the same strength would carry.
The DS 7 Crossback E-Tense 4x4 runs a 5x108 bolt pattern, 65.1mm center bore, and a 20x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 21x9.0J ET35, which tucks the tire under the fender lip on a stock-height DS 7 Crossback E-Tense 4x4. Our Maximum Aggressive reference is 21x9.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
DS 7 Crossback E-Tense 4x4 OE Wheel Specs
The 2019 DS 7 Crossback E-Tense 4x4 (PHEV SUV) uses a 5x108 bolt pattern with a 65.1mm center bore. Factory wheels are 20x8.0J F/R.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the DS 7 Crossback E-Tense 4x4 (2019) we drill the 5x108 pattern and cut the centre bore to 65.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 20x8.0J ET44 → ~6.23″ backspacing
- Flush: 21x9.0J ET35 → ~6.38″ backspacing
- Max: 21x9.5J ET30 → ~6.43″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact DS spec, or want a wheel built to a custom offset for your DS 7 Crossback E-Tense 4x4? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the DS 7 Crossback E-Tense 4x4 (5x108, 65.1 mm Bore)
In our database, 113 other vehicle entries from 15 makes use exactly the same 5x108 bolt pattern and 65.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x108 is used by 7.7% of the vehicle pages in our English fitment guide (499 of 6,503); 22.8% of those also use a 65.1 mm center bore.
Hub-Centric Rings for a 65.1 mm Center Bore
A wheel with a center bore larger than 65.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 66.1 mm | 66.1 → 65.1 mm |
| 66.6 mm | 66.6 → 65.1 mm |
| 67.1 mm | 67.1 → 65.1 mm |
| 70.1 mm | 70.1 → 65.1 mm |
| 73.1 mm | 73.1 → 65.1 mm |
ANKUSI forged wheels are bored to exactly 65.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the DS 7 Crossback E-Tense 4x4 use?
The 2019 DS 7 Crossback E-Tense 4x4 uses a 5x108 bolt pattern.
How many lug bolts does the DS 7 Crossback E-Tense 4x4 use?
The DS 7 Crossback E-Tense 4x4 uses a 5-lug bolt pattern (5x108), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the DS 7 Crossback E-Tense 4x4?
The DS 7 Crossback E-Tense 4x4's center bore is 65.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the DS 7 Crossback E-Tense 4x4?
Factory wheels on the DS 7 Crossback E-Tense 4x4 are 20x8.0J F/R.
What is the biggest wheel size I can fit on my DS 7 Crossback E-Tense 4x4 without rubbing?
The most aggressive fitment we recommend without fender work is 21x9.5J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the DS 7 Crossback E-Tense 4x4?
For a flush look with minimal to no rubbing, we recommend 21x9.0J at ET35 offset as a starting point on a stock or mildly lowered DS 7 Crossback E-Tense 4x4.
Do I need wheel spacers for my DS 7 Crossback E-Tense 4x4?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my DS 7 Crossback E-Tense 4x4?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.38" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my DS 7 Crossback E-Tense 4x4?
The DS 7 Crossback E-Tense 4x4 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 20x8 wheels · 20 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.