2023 Dodge Hornet Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Dodge Hornet wheels? This page gives the 2023 Dodge Hornet bolt pattern (5x110), centre bore, factory rim size and the offset range for aftermarket and forged Dodge Hornet rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Dodge Hornet (2023): 5x110 bolt pattern, 65.1mm center bore. Factory wheels: 18x7.5J at ET40 offset, front and rear. Reference fitment ranges.
Bolt Pattern5x110
Wheel Bolt/NutM12x1.5 Nut
Center Bore65.1mm
Wheel Load Rating800–950 kg/wheel (Crossover segment reference)
Year2023
CategoryCrossover
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x7.5J F/R |
| Flush Fitment | 19x8.5J at ET35 offset |
| Maximum Aggressive | 20x9.0J at ET32 offset |
Forged Wheel Designs for the Dodge Hornet
Every design below is forged to order, so it can be machined to the Dodge Hornet's 5x110 bolt pattern and 65.1 mm center bore, with the width and offset calculated for your setup.
Dodge OEM-Style Matte Black Double 5-Spoke Concave Forged Wheels
Concave · Matte Black
Weld Racing-Style Chrome 10-Spoke Lettered Lip Forged Drag Racing Wheels
Drag Racing · Chrome
Dodge OEM-Style 2-Piece Gloss Black Y-Spoke Riveted Lip Forged Wheels
2-Piece · Gloss Black
Weld Racing-Style Gloss Black / Machined 5-Spoke Deep Lip Forged Drag Racing Wheels
Drag Racing · Gloss Black / Machined
Gloss Black Slotted Turbine Disc Forged Wheels
Monoblock · Gloss Black
Dodge OEM-Style Gloss Black 10 Y-Spoke Concave Forged Wheels
Concave · Gloss Black
Weld Racing-Style Gloss Black Milled Y-Mesh Polished Lip Forged Drag Racing Wheels
Drag Racing · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Dodge Hornet's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Dodge Hornet runs a 5x110 bolt pattern, 65.1mm center bore, and a 18x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.5J ET35, which tucks the tire under the fender lip on a stock-height Dodge Hornet. Our Maximum Aggressive reference is 20x9.0J ET32 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Dodge Hornet OE Wheel Specs
The 2023 Dodge Hornet (Crossover) uses a 5x110 bolt pattern with a 65.1mm center bore. Factory wheels are 18x7.5J F/R.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Dodge Hornet (2023) we drill the 5x110 pattern and cut the centre bore to 65.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x7.5J ET40 → ~5.82″ backspacing
- Flush: 19x8.5J ET35 → ~6.13″ backspacing
- Max: 20x9.0J ET32 → ~6.26″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Dodge spec, or want a wheel built to a custom offset for your Dodge Hornet? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Dodge Hornet use?
The 2023 Dodge Hornet uses a 5x110 bolt pattern.
How many lug bolts does the Dodge Hornet use?
The Dodge Hornet uses a 5-lug bolt pattern (5x110), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Dodge Hornet?
The Dodge Hornet's center bore is 65.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Dodge Hornet?
Factory wheels on the Dodge Hornet are 18x7.5J F/R.
What is the biggest wheel size I can fit on my Dodge Hornet without rubbing?
The most aggressive fitment we recommend without fender work is 20x9.0J at ET32 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Dodge Hornet?
For a flush look with minimal to no rubbing, we recommend 19x8.5J at ET35 offset as a starting point on a stock or mildly lowered Dodge Hornet.
Do I need wheel spacers for my Dodge Hornet?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Dodge Hornet?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.13" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Dodge Hornet?
The Dodge Hornet runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.