Dodge OEM-Style Gloss Black 10 Y-Spoke Forged Wheels
Dodge Challenger / Charger Fitment · 5-Lug
2011 Dodge Durango Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Dodge Durango wheels? This page gives the 2011 Dodge Durango bolt pattern (5x127), centre bore, factory rim size and the offset range for aftermarket and forged Dodge Durango rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Dodge Durango (2011): 5x127 bolt pattern, 71.5mm center bore. Factory wheels: 18x8.0J at ET35 offset, front and rear. Reference fitment ranges.
Bolt Pattern5x127
Wheel Bolt/NutM14x1.5 Nut
Center Bore71.5mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2011
CategorySUV
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8.0J F/R |
| Flush Fitment | 20x9.0J at ET30 offset |
| Maximum Aggressive | 22x10.0J at ET25 offset |
Forged wheels for the Dodge DurangoMachined to the 5x127 bolt pattern and 71.5 mm bore · 14–24 inch · offset calculated for your car · 3D drawing before production
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Dodge Durango's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Dodge Durango runs a 5x127 bolt pattern, 71.5mm center bore, and a 18x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x9.0J ET30, which tucks the tire under the fender lip on a stock-height Dodge Durango. Our Maximum Aggressive reference is 22x10.0J ET25 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Dodge Durango OE Wheel Specs
The 2011 Dodge Durango (SUV) uses a 5x127 bolt pattern with a 71.5mm center bore. Factory wheels are 18x8.0J F/R.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Dodge Durango (2011) we drill the 5x127 pattern and cut the centre bore to 71.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look, F/R 20x9.0J ET30 is a commonly used starting point — clearance must be verified on a stock or mildly lowered Dodge Durango.
Maximum Aggressive Fitment
F/R 22x10.0J ET25 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style 18x8.0J ET35
Recommended setup: 18x8.0J ET35 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade 19x8.5J ET33
Recommended setup: 19x8.5J ET33 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 20x9.0J ET30
Recommended setup: 20x9.0J ET30 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 21x9.5J ET28
Recommended setup: 21x9.5J ET28 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 22x10.0J ET25
Recommended setup: 22x10.0J ET25 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 18x8.0J ET35 | 19x8.5J ET33 | 20x9.0J ET30 | 21x9.5J ET28 | 22x10.0J ET25 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 18x8.0J ET35
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 20x9.0J ET30
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 22x10.0J ET25
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
1
What's your primary use? Daily commuting → Tier A/B. Weekend street driving → Tier B/C. Show or occasional track use → Tier D/E.
2
What's your budget? Under $800 → Tier A. $800-3,400 → Tier B/C. $3,400+ → Tier D/E.
3
How much does fuel economy matter? Very important → Tier A. Somewhat important → Tier B/C. Not a priority → Tier D/E.
4
Still unsure? Tier C (Balanced / Flush Fit) is the default choice for most Dodge Durango owners.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x8.0J ET35 → ~5.88″ backspacing
- Flush: 20x9.0J ET30 → ~6.18″ backspacing
- Max: 22x10.0J ET25 → ~6.48″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Dodge spec, or want a wheel built to a custom offset for your Dodge Durango? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Custom Forged Wheels for the Dodge Durango (2011)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x127 pattern and the 71.5mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose — most Dodge orders on this platform land somewhere between the 20x9.0J ET30 flush setup and the 22x10.0J ET25 aggressive setup referenced above.
Designs we already tool for the 5x127 pattern — each one is re-cut to your sizes and offsets:
Weld Racing-Style Gloss Black / Machined Mesh Beadlock Forged Drag Racing Wheels – Ford Mustang / Chevrolet Corvette Fitment (5-Lug) – Design 2
Ford Mustang / Chevrolet Corvette Forged Drag Racing Wheels – Mirror Polished 5-Spoke 3-Piece (5-Lug)
Belak-Style Gloss Black / Machined 5 Split-Spoke Forged Drag Racing Wheels – Ford Mustang / Chevrolet Corvette Fitment (5-Lug)
Belak-Style Gloss Black / Machined Mesh Beadlock Forged Drag Racing Wheels – Ford Mustang / Chevrolet Corvette Fitment (5-Lug)Frequently Asked Questions
What bolt pattern (PCD) does the Dodge Durango use?
The 2011 Dodge Durango uses a 5x127 bolt pattern.
How many lug bolts does the Dodge Durango use?
The Dodge Durango uses a 5-lug bolt pattern (5x127), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Dodge Durango?
The Dodge Durango's center bore is 71.5mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Dodge Durango?
Factory wheels on the Dodge Durango are 18x8.0J F/R.
What is the biggest wheel size I can fit on my Dodge Durango without rubbing?
The most aggressive fitment we recommend without fender work is 22x10.0J at ET25 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Dodge Durango?
For a flush look with minimal to no rubbing, we recommend 20x9.0J at ET30 offset as a starting point on a stock or mildly lowered Dodge Durango.
Do I need wheel spacers for my Dodge Durango?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Dodge Durango?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.18" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Dodge Durango?
The Dodge Durango runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Forged Wheel Designs for the Dodge Durango
Every design below is forged to order, so it can be machined to the Dodge Durango's 5x127 bolt pattern and 71.5 mm center bore, with the width and offset calculated for your setup.
Weld Racing-Style Gloss Black / Machined Mesh Beadlock Forged Drag Racing Wheels
Ford Mustang / Chevrolet Corvette Fitment · 5-Lug
Ford Mustang / Chevrolet Corvette Forged Drag Racing Wheels
Gloss Black / Machined Multi-Spoke Deep Lip · 5-Lug
Dodge OEM-Style Matte Silver Directional Milled Forged Wheels – Design 4
Dodge Challenger / Charger Fitment · 5-Lug
Belak-Style Gloss Black / Machined Mesh Beadlock Forged Drag Racing Wheels
Ford Mustang / Chevrolet Corvette Fitment · 5-Lug
Belak-Style Gloss Black / Machined 5 Split-Spoke Forged Drag Racing Wheels
Ford Mustang / Chevrolet Corvette Fitment · 5-Lug
Ford Mustang / Chevrolet Corvette Forged Drag Racing Wheels
Mirror Polished 5-Spoke 3-Piece · 5-Lug
Ford Mustang / Chevrolet Corvette Forged Drag Racing Wheels – Design 2
Chrome Aero Dish · 5-Lug