
2009 Dacia Logan MCV Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Dacia Logan MCV wheels? This page gives the 2009 Dacia Logan MCV bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Dacia Logan MCV rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Dacia Logan MCV (2009): 4x100 bolt pattern, 60.1mm center bore. Factory wheels: 15x6.0J F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 15x6.0J F/R |
| Flush Fitment | 16x7.0J at ET38 offset |
| Maximum Aggressive | 17x7.0J at ET35 offset |
Forged Wheel Designs for the Dacia Logan MCV
Every design below is forged to order, so it can be machined to the Dacia Logan MCV's 4x100 bolt pattern and 60.1 mm center bore, with the width and offset calculated for your setup.


Rotiform-Style Gloss White 6-Spoke Forged Wheels
Monoblock · Gloss White

BBS LM-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal

BBS-Style Gold Mesh Polished Lip Forged Wheels
Monoblock · Gold

BBS-Style Gold Mesh Polished Lip 2-Piece Forged Wheels
2-Piece · Gold

OZ Racing-Style Gloss White 15-Spoke Forged Wheels
Monoblock · Gloss White

Bronze Gold Cross-Spoke Forged Wheels
Monoblock · Bronze Gold

Rays-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


ANKUSI Engineering Expert Advice
A wagon carries wagon-specific weight distribution — more mass over the rear axle when loaded — so wheel strength at the rear corners matters as much as the front. Forging lets us match the factory's strength target on both ends while keeping rotational mass down, which keeps the ride composed whether the cargo area is empty or full.
The Dacia Logan MCV runs a 4x100 bolt pattern, 60.1mm center bore, and a 15x6.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 16x7.0J ET38, which tucks the tire under the fender lip on a stock-height Dacia Logan MCV. Our Maximum Aggressive reference is 17x7.0J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Dacia Logan MCV OE Wheel Specs
The 2009 Dacia Logan MCV (Wagon) uses a 4x100 bolt pattern with a 60.1mm center bore. Factory wheels are 15x6.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Dacia Logan MCV (2009) we drill the 4x100 pattern and cut the centre bore to 60.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 15x6.0J ET43 → ~5.19″ backspacing
- Flush: 16x7.0J ET38 → ~5.5″ backspacing
- Max: 17x7.0J ET35 → ~5.38″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Dacia spec, or want a wheel built to a custom offset for your Dacia Logan MCV? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.