Chevrolet SS (2016) Wheel Fitment
Chevrolet SS (2016): 5x120 bolt pattern, 66.9mm center bore. Factory wheels: F: 19x8.5J R: 19x9.0J. Reference fitment ranges.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 19x8.5J R: 19x9.0J |
| Flush Fitment | F 20x9.5J ET38 / R 20x10.5J ET45 |
| Maximum Aggressive | F 20x10.0J ET35 / R 20x11.0J ET40 |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Chevrolet SS's factory wheel spec reflects a deliberate balance between comfort, steering feel and durability that the engineering team tuned for. Forging lets ANKUSI match that same strength target while trimming rotational mass — the part of a wheel upgrade that actually changes how the car drives, not just how it looks.
The Chevrolet SS runs a 5x120 bolt pattern, 66.9mm center bore, and a F: 19x8.5J wheel from the factory. Our Flush Fitment reference is F 20x9.5J ET38 / R 20x10.5J ET45, which tucks the tire under the fender lip on a stock-height Chevrolet SS. Our Maximum Aggressive reference is F 20x10.0J ET35 / R 20x11.0J ET40 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Chevrolet SS OE Wheel Specs
The 2016 Chevrolet SS (Sedan) uses a 5x120 bolt pattern with a 66.9mm center bore. Factory wheels are F: 19x8.5J R: 19x9.0J.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
Flush Fitment
For a flush look, F 20x9.5J ET38 / R 20x10.5J ET45 is a commonly used starting point — clearance must be verified on a stock or mildly lowered Chevrolet SS.
Maximum Aggressive Fitment
F 20x10.0J ET35 / R 20x11.0J ET40 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style F 19x8.5J ET48 / R 19x9.0J ET57
Recommended setup: F 19x8.5J ET48 / R 19x9.0J ET57 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade F 20x9.0J ET43 / R 20x10.0J ET51
Recommended setup: F 20x9.0J ET43 / R 20x10.0J ET51 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit F 20x9.5J ET38 / R 20x10.5J ET45
Recommended setup: F 20x9.5J ET38 / R 20x10.5J ET45 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive F 20x10.0J ET37 / R 20x11.0J ET43
Recommended setup: F 20x10.0J ET37 / R 20x11.0J ET43 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive F 20x10.0J ET35 / R 20x11.0J ET40
Recommended setup: F 20x10.0J ET35 / R 20x11.0J ET40 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | F 19x8.5J ET48 / R 19x9.0J ET57 | F 20x9.0J ET43 / R 20x10.0J ET51 | F 20x9.5J ET38 / R 20x10.5J ET45 | F 20x10.0J ET37 / R 20x11.0J ET43 | F 20x10.0J ET35 / R 20x11.0J ET40 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: F 19x8.5J ET48 / R 19x9.0J ET57
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: F 20x9.5J ET38 / R 20x10.5J ET45
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: F 20x10.0J ET35 / R 20x11.0J ET40
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 19x8.5J ET48 → ~6.64″ F backspacing, R 19x9.0J ET57 → ~7.24″ R backspacing
- Flush: F 20x9.5J ET38 → ~6.75″ F backspacing, R 20x10.5J ET45 → ~7.52″ R backspacing
- Max: F 20x10.0J ET35 → ~6.88″ F backspacing, R 20x11.0J ET40 → ~7.57″ R backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Chevrolet spec, or want a wheel built to a custom offset for your Chevrolet SS? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Chevrolet SS use?
How many lug bolts does the Chevrolet SS use?
What is the center bore size on the Chevrolet SS?
What size are the factory (stock) wheels on the Chevrolet SS?
What is the biggest wheel size I can fit on my Chevrolet SS without rubbing?
What does a flush wheel fitment look like on the Chevrolet SS?
Do I need wheel spacers for my Chevrolet SS?
How do I calculate wheel backspacing for my Chevrolet SS?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Chevrolet SS?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 136 Nm (100 ft-lb). Covers most Chevrolet passenger cars and crossovers on M12 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.