Gloss Black / Machined Mesh Riveted Forged Wheels
Monoblock · Gloss Black / Machined
2015 Chevrolet Corvette Z06 Convertible Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Chevrolet Corvette Z06 Convertible wheels? This page gives the 2015 Chevrolet Corvette Z06 Convertible bolt pattern (5x120.65), centre bore, factory rim size and the offset range for aftermarket and forged Chevrolet Corvette Z06 Convertible rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Chevrolet Corvette Z06 Convertible (2015): 5x120.65 bolt pattern, 70.3mm center bore. Factory wheels: F: 19x10.0J R: 20x12.0J. Reference fitment ranges.
Bolt Pattern5x120.65
Wheel Bolt/NutM12x1.5 Nut
Center Bore70.3mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Caliper TypeBrembo 6-piston fixed front / 4-piston fixed rear (OEM)
Year2015
CategoryConvertible
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 19x10.0J R: 20x12.0J |
| Flush Fitment | F 19x10.5J ET35 / R 20x12.5J ET70 |
| Maximum Aggressive | F 20x11.0J ET30 / R 21x13.0J ET65 |
Forged Wheel Designs for the Chevrolet Corvette Z06 Convertible
Every design below is forged to order, so it can be machined to the Chevrolet Corvette Z06 Convertible's 5x120.65 bolt pattern and 70.3 mm center bore, with the width and offset calculated for your setup.
Weld Racing-Style 10 Y-Spoke Mirror Milled Forged Drag Racing Wheels
Drag Racing · Custom Finish
Chevrolet OEM-Style Gloss Black 5-Spoke Machined Face Forged Wheels
Monoblock · Gloss Black
Corvette OEM-Style Mirror Polished 5 Y-Spoke Deep Lip 2-Piece Forged Wheels
2-Piece · Mirror Polished
Belak Gloss White Full-Face Forged Drag Racing Wheels
Drag Racing · Gloss White
BBS-Style Metallic Gray Cross-Spoke Mesh Stepped Lip Forged Wheels
Monoblock · Metallic Gray
Chevrolet OEM-Style Black Chrome 5 Split V-Spoke Forged Wheels
Monoblock · Black Chrome
Black / Machined Petal Forged Wheels
Monoblock · Black Machined
See all Chevrolet Corvette wheel designs Corvette OEM-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
With less structural stiffness from the missing roof, a convertible's suspension tuning leans more heavily on unsprung mass control. Forged construction keeps wheel weight down at the same strength rating, which is one less variable working against the Chevrolet Corvette Z06 Convertible's chassis.
The Chevrolet Corvette Z06 Convertible runs a 5x120.65 bolt pattern, 70.3mm center bore, and a F: 19x10.0J wheel from the factory. Our Flush Fitment reference is F 19x10.5J ET35 / R 20x12.5J ET70, which tucks the tire under the fender lip on a stock-height Chevrolet Corvette Z06 Convertible. Our Maximum Aggressive reference is F 20x11.0J ET30 / R 21x13.0J ET65 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Chevrolet Corvette Z06 Convertible OE Wheel Specs
The 2015 Chevrolet Corvette Z06 Convertible (Convertible) uses a 5x120.65 bolt pattern with a 70.3mm center bore. Factory wheels are F: 19x10.0J R: 20x12.0J.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Chevrolet Corvette Z06 Convertible (2015) we drill the 5x120.65 pattern and cut the centre bore to 70.3mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 19x10.0J ET43 → ~7.19″ F backspacing, R 20x12.0J ET79 → ~9.61″ R backspacing
- Flush: F 19x10.5J ET35 → ~7.13″ F backspacing, R 20x12.5J ET70 → ~9.51″ R backspacing
- Max: F 20x11.0J ET30 → ~7.18″ F backspacing, R 21x13.0J ET65 → ~9.56″ R backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Chevrolet spec, or want a wheel built to a custom offset for your Chevrolet Corvette Z06 Convertible? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Chevrolet Corvette Z06 Convertible use?
The 2015 Chevrolet Corvette Z06 Convertible uses a 5x120.65 bolt pattern.
How many lug bolts does the Chevrolet Corvette Z06 Convertible use?
The Chevrolet Corvette Z06 Convertible uses a 5-lug bolt pattern (5x120.65), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Chevrolet Corvette Z06 Convertible?
The Chevrolet Corvette Z06 Convertible's center bore is 70.3mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Chevrolet Corvette Z06 Convertible?
Factory wheels on the Chevrolet Corvette Z06 Convertible are F: 19x10.0J R: 20x12.0J.
What is the biggest wheel size I can fit on my Chevrolet Corvette Z06 Convertible without rubbing?
The most aggressive fitment we recommend without fender work is F 20x11.0J ET30 / R 21x13.0J ET65. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Chevrolet Corvette Z06 Convertible?
For a flush look with minimal to no rubbing, we recommend F 19x10.5J ET35 / R 20x12.5J ET70 as a starting point on a stock or mildly lowered Chevrolet Corvette Z06 Convertible.
Do I need wheel spacers for my Chevrolet Corvette Z06 Convertible?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Chevrolet Corvette Z06 Convertible?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 7.13" backspacing up front and 9.51" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Chevrolet Corvette Z06 Convertible?
Yes — the Chevrolet Corvette Z06 Convertible's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 136 Nm (100 ft-lb). Covers most Chevrolet passenger cars and crossovers on M12 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.