Fang Cheng Bao OEM-Style Gloss Black Multi-Spoke Bolt-Ring Off-Road Forged Wheels
Off-Road · Gloss Black
2025 BYD Shark 6 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting BYD Shark 6 wheels? This page gives the 2025 BYD Shark 6 bolt pattern (6x139.7), centre bore, factory rim size and the offset range for aftermarket and forged BYD Shark 6 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2025 BYD Shark 6 uses a 6x139.7 bolt pattern with a 106.1 mm centre bore. Factory wheels: 18x8J ET45. For aftermarket wheels, 18x9J ET18 sits flush.
Forged wheels for the 2025 BYD Shark 6 — drilled 6x139.7 with a 106.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
BYD Shark 6 (2025): 6x139.7 bolt pattern, 106.1mm center bore, OE 18x8J ET45. Forged wheel fitment specs from ANKUSI.
Bolt Pattern6x139.7
Center Bore106.1mm
Year2025
CategoryTruck
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8J ET45 |
| Flush Fitment | 18x9J at ET18 offset |
Forged Wheel Designs for the BYD Shark 6
Every design below is forged to order, so it can be machined to the BYD Shark 6's 6x139.7 bolt pattern and 106.1 mm center bore, with the width and offset calculated for your setup.
Bronze / Gloss Black Forged Wheels
Off-Road Beadlock · Bronze / Gloss Black
Gloss Black 16-Window Forged Wheels
Off-Road · Gloss Black
10-Spoke Mesh Beadlock Gloss Black Milled Forged Wheels
Off-Road Beadlock · Custom Finish
Gloss White Semi-Full-Face Forged Wheels
Off-Road · Gloss White
TRD-Style Gloss Black Hex-Window Off-Road Forged Wheels
Off-Road · Gloss Black
Fuel Black / Machined Petal Machined Face Off-Road Forged Wheels
Off-Road · Black Machined
Forgestar-Style Gloss Black Mesh Beadlock Off-Road Forged Wheels
Off-Road Beadlock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a truck platform, wheel weight sits right at the unsprung mass budget the suspension engineers already spent on payload and towing capacity. A forged wheel keeps that budget intact — same strength, less rotational inertia — instead of eating into the margin the way a cheap cast aftermarket wheel can.
The BYD Shark 6 ships from the factory on a 6x139.7 bolt pattern with a 106.1mm center bore and a 18x8J ET45 wheel. Our flush reference for the BYD Shark 6 is 18x9J ET18.; our maximum aggressive reference is 20x9J ET12. — beyond that, expect clearance issues against the fender liner without further modification.
BYD Shark 6 OE Wheel Specs
The BYD Shark 6 ships from the factory on 6x139.7 bolt pattern wheels with a 106.1mm center bore. The stock wheel size is 18x8J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the BYD Shark 6 (2025) we drill the 6x139.7 pattern and cut the centre bore to 106.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 18x8J | ET45 | 6.27 in (159 mm) | — | — |
| Flush | 18x9J | ET18 | 5.71 in (145 mm) | −14 mm | +40 mm |
| Maximum | 20x9J | ET12 | 5.47 in (139 mm) | −20 mm | +46 mm |
Vehicles With the Same Hub as the BYD Shark 6 (6x139.7, 106.1 mm Bore)
In our database, 32 other vehicle entries from 7 makes use exactly the same 6x139.7 bolt pattern and 106.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
6x139.7 is used by 4.0% of the vehicle pages in our English fitment guide (258 of 6,503); 12.8% of those also use a 106.1 mm center bore.
Hub-Centric Rings for a 106.1 mm Center Bore
A wheel with a center bore larger than 106.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 108.1 mm | 108.1 → 106.1 mm |
| 110.1 mm | 110.1 → 106.1 mm |
| 130.1 mm | 130.1 → 106.1 mm |
ANKUSI forged wheels are bored to exactly 106.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the BYD Shark 6 use?
The 2025 BYD Shark 6 uses a 6x139.7 bolt pattern.
How many lug bolts does the BYD Shark 6 use?
The BYD Shark 6 uses a 6-lug bolt pattern (6x139.7), so you need a 6-lug forged wheel to bolt straight on.
What is the center bore size on the BYD Shark 6?
The BYD Shark 6's center bore is 106.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the BYD Shark 6?
Factory wheels on the BYD Shark 6 are 18x8J ET45.
What does a flush wheel fitment look like on the BYD Shark 6?
For a flush look with minimal to no rubbing, we recommend 18x9J at ET18 offset as a starting point on a stock or mildly lowered BYD Shark 6.
Do I need wheel spacers for my BYD Shark 6?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my BYD Shark 6?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.71" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my BYD Shark 6?
The BYD Shark 6 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x8 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.