Brabus-Style Gloss Black Carbon-Ring 10-Spoke Red Pinstripe Forged Wheels
Monoblock · Gloss Black
2004 Brabus Mercedes-Benz Viano V8 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Brabus Mercedes-Benz Viano V8 wheels? This page gives the 2004 Brabus Mercedes-Benz Viano V8 bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Brabus Mercedes-Benz Viano V8 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2004 Brabus Mercedes-Benz Viano V8 uses a 5x112 bolt pattern with a 66.6 mm centre bore and M14x1.5 lug bolts. Factory wheels: 19x8.5J, front and rear. For aftermarket wheels, 20x9.0J ET40 sits flush and 20x9.5J ET35 is the most aggressive fit.
Forged wheels for the 2004 Brabus Mercedes-Benz Viano V8 — drilled 5x112 with a 66.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Brabus Mercedes-Benz Viano V8 (2004): 5x112 bolt pattern, 66.6mm center bore. Factory wheels: 19x8.5J F/R. Reference fitment ranges.
Bolt Pattern5x112
Wheel Bolt/NutM14x1.5 Bolt
Center Bore66.6mm
Wheel Load Rating900–1100 kg/wheel (Van / MPV segment reference)
Year2004
CategoryVan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x8.5J F/R |
| Flush Fitment | 20x9.0J at ET40 offset |
| Maximum Aggressive | 20x9.5J at ET35 offset |
Forged Wheel Designs for the Brabus Mercedes-Benz Viano V8
Every design below is forged to order, so it can be machined to the Brabus Mercedes-Benz Viano V8's 5x112 bolt pattern and 66.6 mm center bore, with the width and offset calculated for your setup.
Gray 2-Piece 10 Y-Spoke Forged Wheels
2-Piece · Gray
Gloss White 3-Spoke Center-Lock Forged Wheels
Center-Lock · Gloss White
Black / Machined 5 Twin-Spoke Directional Forged Wheels
Monoblock · Black Machined
Edelweiss-Style LT3 Bronze Gold 5 Y-Spoke Daisy-Spoke Forged Wheels
Replica · Bronze Gold
WF R2-Style Matte Silver Side-Milled Forged Wheels
Replica · Matte Silver
Matte Silver Full-Face Deep Lip Forged Wheels
Deep Dish · Matte Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A minivan's wheel spec has to work across a wide load range — empty commute or full family trip. Forged construction preserves the factory's load-rating margin while cutting rotational weight, which keeps ride quality consistent across that range.
The Brabus Mercedes-Benz Viano V8 runs a 5x112 bolt pattern, 66.6mm center bore, and a 19x8.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x9.0J ET40, which tucks the tire under the fender lip on a stock-height Brabus Mercedes-Benz Viano V8. Our Maximum Aggressive reference is 20x9.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Brabus Mercedes-Benz Viano V8 OE Wheel Specs
The 2004 Brabus Mercedes-Benz Viano V8 (Van) uses a 5x112 bolt pattern with a 66.6mm center bore. Factory wheels are 19x8.5J F/R.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Brabus Mercedes-Benz Viano V8 (2004) we drill the 5x112 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 19x8.5J ET45 → ~6.52″ backspacing
- Flush: 20x9.0J ET40 → ~6.57″ backspacing
- Max: 20x9.5J ET35 → ~6.63″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Brabus spec, or want a wheel built to a custom offset for your Brabus Mercedes-Benz Viano V8? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Brabus Mercedes-Benz Viano V8 (5x112, 66.6 mm Bore)
In our database, 823 other vehicle entries from 21 makes use exactly the same 5x112 bolt pattern and 66.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 58.6% of those also use a 66.6 mm center bore.
Hub-Centric Rings for a 66.6 mm Center Bore
A wheel with a center bore larger than 66.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 67.1 mm | 67.1 → 66.6 mm |
| 70.1 mm | 70.1 → 66.6 mm |
| 70.5 mm | 70.5 → 66.6 mm |
| 71.6 mm | 71.6 → 66.6 mm |
| 73.1 mm | 73.1 → 66.6 mm |
ANKUSI forged wheels are bored to exactly 66.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Brabus Mercedes-Benz Viano V8 use?
The 2004 Brabus Mercedes-Benz Viano V8 uses a 5x112 bolt pattern.
How many lug bolts does the Brabus Mercedes-Benz Viano V8 use?
The Brabus Mercedes-Benz Viano V8 uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Brabus Mercedes-Benz Viano V8?
The Brabus Mercedes-Benz Viano V8's center bore is 66.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Brabus Mercedes-Benz Viano V8?
Factory wheels on the Brabus Mercedes-Benz Viano V8 are 19x8.5J F/R.
What is the biggest wheel size I can fit on my Brabus Mercedes-Benz Viano V8 without rubbing?
The most aggressive fitment we recommend without fender work is 20x9.5J at ET35 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Brabus Mercedes-Benz Viano V8?
For a flush look with minimal to no rubbing, we recommend 20x9.0J at ET40 offset as a starting point on a stock or mildly lowered Brabus Mercedes-Benz Viano V8.
Do I need wheel spacers for my Brabus Mercedes-Benz Viano V8?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Brabus Mercedes-Benz Viano V8?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.57" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Brabus Mercedes-Benz Viano V8?
The Brabus Mercedes-Benz Viano V8 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x8.5 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.