Bentley Mulsanne Diamond Jubilee (2012) Bolt Pattern & Wheel Fitment
Bentley Mulsanne Diamond Jubilee (2012): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: 20x8.5J F/R. Reference fitment ranges.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 20x8.5J F/R |
| Flush Fitment | 21x9.0J at ET30 offset |
| Maximum Aggressive | 22x9.5J at ET25 offset |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Bentley Mulsanne Diamond Jubilee runs a 5x130 bolt pattern, 71.6mm center bore, and a 20x8.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 21x9.0J ET30, which tucks the tire under the fender lip on a stock-height Bentley Mulsanne Diamond Jubilee. Our Maximum Aggressive reference is 22x9.5J ET25 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Bentley Mulsanne Diamond Jubilee OE Wheel Specs
The 2012 Bentley Mulsanne Diamond Jubilee (Luxury Sedan) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are 20x8.5J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday drivability
- A commonly used size for this vehicle class, supporting parts and tire availability
- Maintains clearance for the factory suspension and brake components
- Provides stable, predictable handling across normal driving conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Bentley Mulsanne Diamond Jubilee (2012) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look with minimal rubbing, F/R 21x9.0J ET30 is the recommended starting point on a stock or mildly lowered Bentley Mulsanne Diamond Jubilee.
Maximum Aggressive Fitment
F/R 22x9.5J ET25 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style 20x8.5J ET35
Recommended setup: 20x8.5J ET35 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade 21x9.0J ET33
Recommended setup: 21x9.0J ET33 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 21x9.0J ET30
Recommended setup: 21x9.0J ET30 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 22x9.5J ET28
Recommended setup: 22x9.5J ET28 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 22x9.5J ET25
Recommended setup: 22x9.5J ET25 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 20x8.5J ET35 | 21x9.0J ET33 | 21x9.0J ET30 | 22x9.5J ET28 | 22x9.5J ET25 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 20x8.5J ET35
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 21x9.0J ET30
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 22x9.5J ET25
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 20x8.5J ET35 → ~6.13″ backspacing
- Flush: 21x9.0J ET30 → ~6.18″ backspacing
- Max: 22x9.5J ET25 → ~6.23″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Bentley spec, or want a wheel built to a custom offset for your Bentley Mulsanne Diamond Jubilee? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Custom Forged Wheels for the Bentley Mulsanne Diamond Jubilee (2012)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x130 pattern and the 71.6mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose — most Bentley orders on this platform land somewhere between the 21x9.0J ET30 flush setup and the 22x9.5J ET25 aggressive setup referenced above.
Designs we already tool for the 5x130 pattern — each one is re-cut to your sizes and offsets:
APEX Gloss Black 5 Y-Spoke Forged Wheels – BMW M3 / Audi RS5 Fitment (5-Lug)
APEX Gloss Black / Gunmetal 5 Y-Spoke Forged Wheels – BMW M3 / Audi RS5 Fitment (5-Lug)
Porsche Style Matte Silver 10-Spoke Directional Forged Wheels – Porsche 911 / Porsche Panamera Fitment (5-Lug)
APEX Polished Silver 8 Y-Spoke Forged Wheels – BMW M3 / Audi RS5 Fitment (5-Lug)