2002 Alfa Romeo 147 JTD 16V Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Alfa Romeo 147 JTD 16V wheels? This page gives the 2002 Alfa Romeo 147 JTD 16V bolt pattern (5x98), centre bore, factory rim size and the offset range for aftermarket and forged Alfa Romeo 147 JTD 16V rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2002 Alfa Romeo 147 JTD 16V uses a 5x98 bolt pattern with a 58.1 mm centre bore and M12x1.5 lug nuts. Factory wheels: 15x6.0J, front and rear. For aftermarket wheels, 17x7.5J ET35 sits flush and 18x8.0J ET30 is the most aggressive fit.
Forged wheels for the 2002 Alfa Romeo 147 JTD 16V — drilled 5x98 with a 58.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Alfa Romeo 147 JTD 16V (2002): 5x98 bolt pattern, 58.1mm center bore. Factory wheels: 15x6.0J F/R. Reference fitment ranges.
Bolt Pattern5x98
Wheel Bolt/NutM12x1.5 Nut
Center Bore58.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2002
CategoryHatchback
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 15x6.0J F/R |
| Flush Fitment | 17x7.5J at ET35 offset |
| Maximum Aggressive | 18x8.0J at ET30 offset |
Forged Wheel Designs for the Alfa Romeo 147 JTD 16V
Every design below is forged to order, so it can be machined to the Alfa Romeo 147 JTD 16V's 5x98 bolt pattern and 58.1 mm center bore, with the width and offset calculated for your setup.
Transparent Copper Petal Forged Wheels
Monoblock · Transparent Copper
Matte Gray Cross-Spoke Forged Wheels
Monoblock · Matte Gray
Cosmis-Style Polished 12-Spoke Machined Off-Road Forged Wheels
Off-Road · Polished
Silver 5 Y-Spoke Mirror Polished Forged Wheels
Monoblock · Silver
Gloss Black Custom Forged Wheels
Monoblock · Gloss Black
Black / Machined Petal Forged Wheels
Monoblock · Black Machined
Gloss Black Forged Wheels
Monoblock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Hot hatches and performance compacts are built around quick direction changes, so rotational mass at the wheel has an outsized effect on how the car actually feels to drive. Forging trims that mass while holding the same strength margin as the factory wheel, which is exactly the trade-off this kind of platform rewards.
The Alfa Romeo 147 JTD 16V runs a 5x98 bolt pattern, 58.1mm center bore, and a 15x6.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 17x7.5J ET35, which tucks the tire under the fender lip on a stock-height Alfa Romeo 147 JTD 16V. Our Maximum Aggressive reference is 18x8.0J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Alfa Romeo 147 JTD 16V OE Wheel Specs
The 2002 Alfa Romeo 147 JTD 16V (Hatchback) uses a 5x98 bolt pattern with a 58.1mm center bore. Factory wheels are 15x6.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Alfa Romeo 147 JTD 16V (2002) we drill the 5x98 pattern and cut the centre bore to 58.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 15x6.0J ET40.5 → ~5.09″ backspacing
- Flush: 17x7.5J ET35 → ~5.63″ backspacing
- Max: 18x8.0J ET30 → ~5.68″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Alfa Romeo spec, or want a wheel built to a custom offset for your Alfa Romeo 147 JTD 16V? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Alfa Romeo 147 JTD 16V (5x98, 58.1 mm Bore)
In our database, 30 other vehicle entries from 6 makes use exactly the same 5x98 bolt pattern and 58.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x98 is used by 0.5% of the vehicle pages in our English fitment guide (32 of 6,503); 96.9% of those also use a 58.1 mm center bore.
Hub-Centric Rings for a 58.1 mm Center Bore
A wheel with a center bore larger than 58.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 60.1 mm | 60.1 → 58.1 mm |
| 63.4 mm | 63.4 → 58.1 mm |
| 64.1 mm | 64.1 → 58.1 mm |
| 65.1 mm | 65.1 → 58.1 mm |
| 73.1 mm | 73.1 → 58.1 mm |
ANKUSI forged wheels are bored to exactly 58.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Alfa Romeo 147 JTD 16V use?
The 2002 Alfa Romeo 147 JTD 16V uses a 5x98 bolt pattern.
How many lug bolts does the Alfa Romeo 147 JTD 16V use?
The Alfa Romeo 147 JTD 16V uses a 5-lug bolt pattern (5x98), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Alfa Romeo 147 JTD 16V?
The Alfa Romeo 147 JTD 16V's center bore is 58.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Alfa Romeo 147 JTD 16V?
Factory wheels on the Alfa Romeo 147 JTD 16V are 15x6.0J F/R.
What is the biggest wheel size I can fit on my Alfa Romeo 147 JTD 16V without rubbing?
The most aggressive fitment we recommend without fender work is 18x8.0J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Alfa Romeo 147 JTD 16V?
For a flush look with minimal to no rubbing, we recommend 17x7.5J at ET35 offset as a starting point on a stock or mildly lowered Alfa Romeo 147 JTD 16V.
Do I need wheel spacers for my Alfa Romeo 147 JTD 16V?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Alfa Romeo 147 JTD 16V?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.63" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Alfa Romeo 147 JTD 16V?
The Alfa Romeo 147 JTD 16V runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 15x6 wheels · 15 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.