2002 Alfa Romeo 147 GTA Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Alfa Romeo 147 GTA wheels? This page gives the 2002 Alfa Romeo 147 GTA bolt pattern (5x98), centre bore, factory rim size and the offset range for aftermarket and forged Alfa Romeo 147 GTA rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2002 Alfa Romeo 147 GTA uses a 5x98 bolt pattern with a 58.1 mm centre bore and M12x1.5 lug nuts. Factory wheels: 17x7.5J, front and rear. For aftermarket wheels, 18x8.0J ET32 sits flush and 18x8.5J ET28 is the most aggressive fit.
Forged wheels for the 2002 Alfa Romeo 147 GTA — drilled 5x98 with a 58.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Alfa Romeo 147 GTA (2002): 5x98 bolt pattern, 58.1mm center bore. Factory wheels: 17x7.5J F/R. Reference fitment ranges.
Bolt Pattern5x98
Wheel Bolt/NutM12x1.5 Nut
Center Bore58.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2002
CategoryPerformance Hatch
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x7.5J F/R |
| Flush Fitment | 18x8.0J at ET32 offset |
| Maximum Aggressive | 18x8.5J at ET28 offset |
Forged Wheel Designs for the Alfa Romeo 147 GTA
Every design below is forged to order, so it can be machined to the Alfa Romeo 147 GTA's 5x98 bolt pattern and 58.1 mm center bore, with the width and offset calculated for your setup.
Gloss Black Forged Wheels
Monoblock · Gloss Black
Transparent Gray 10-Spoke Forged Wheels
Monoblock · Transparent Gray
Satin Black Polished Lip 16-Spoke Forged Wheels
Off-Road · Satin Black
Bright Silver Custom Forged Wheels
Monoblock · Bright Silver
Polished 5-Hole Turbine Forged Wheels
Monoblock · Polished
Gloss Black Custom Forged Wheels
Monoblock · Gloss Black
Black / Machined Petal Forged Wheels
Monoblock · Black Machined
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a compact performance platform, every pound of rotational mass fights the car's natural agility. A forged wheel keeps strength at the factory-rated level while cutting that rotational weight, which is where the driving-feel improvement actually comes from.
The Alfa Romeo 147 GTA runs a 5x98 bolt pattern, 58.1mm center bore, and a 17x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x8.0J ET32, which tucks the tire under the fender lip on a stock-height Alfa Romeo 147 GTA. Our Maximum Aggressive reference is 18x8.5J ET28 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Alfa Romeo 147 GTA OE Wheel Specs
The 2002 Alfa Romeo 147 GTA (Performance Hatch) uses a 5x98 bolt pattern with a 58.1mm center bore. Factory wheels are 17x7.5J F/R.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Alfa Romeo 147 GTA (2002) we drill the 5x98 pattern and cut the centre bore to 58.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 17x7.5J ET35 → ~5.63″ backspacing
- Flush: 18x8.0J ET32 → ~5.76″ backspacing
- Max: 18x8.5J ET28 → ~5.85″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Alfa Romeo spec, or want a wheel built to a custom offset for your Alfa Romeo 147 GTA? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Alfa Romeo 147 GTA (5x98, 58.1 mm Bore)
In our database, 30 other vehicle entries from 6 makes use exactly the same 5x98 bolt pattern and 58.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x98 is used by 0.5% of the vehicle pages in our English fitment guide (32 of 6,503); 96.9% of those also use a 58.1 mm center bore.
Hub-Centric Rings for a 58.1 mm Center Bore
A wheel with a center bore larger than 58.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 60.1 mm | 60.1 → 58.1 mm |
| 63.4 mm | 63.4 → 58.1 mm |
| 64.1 mm | 64.1 → 58.1 mm |
| 65.1 mm | 65.1 → 58.1 mm |
| 73.1 mm | 73.1 → 58.1 mm |
ANKUSI forged wheels are bored to exactly 58.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Alfa Romeo 147 GTA use?
The 2002 Alfa Romeo 147 GTA uses a 5x98 bolt pattern.
How many lug bolts does the Alfa Romeo 147 GTA use?
The Alfa Romeo 147 GTA uses a 5-lug bolt pattern (5x98), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Alfa Romeo 147 GTA?
The Alfa Romeo 147 GTA's center bore is 58.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Alfa Romeo 147 GTA?
Factory wheels on the Alfa Romeo 147 GTA are 17x7.5J F/R.
What is the biggest wheel size I can fit on my Alfa Romeo 147 GTA without rubbing?
The most aggressive fitment we recommend without fender work is 18x8.5J at ET28 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Alfa Romeo 147 GTA?
For a flush look with minimal to no rubbing, we recommend 18x8.0J at ET32 offset as a starting point on a stock or mildly lowered Alfa Romeo 147 GTA.
Do I need wheel spacers for my Alfa Romeo 147 GTA?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Alfa Romeo 147 GTA?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.76" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Alfa Romeo 147 GTA?
The Alfa Romeo 147 GTA runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 17x7.5 wheels · 17 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.