
Gloss Black Deep Lip Forged Wheels
Deep Dish · Gloss Black
Fitting ABT VW New Beetle Cabriolet wheels? This page gives the 2003 ABT VW New Beetle Cabriolet bolt pattern (5x100), centre bore, factory rim size and the offset range for aftermarket and forged ABT VW New Beetle Cabriolet rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
ABT VW New Beetle Cabriolet (2003): 5x100 bolt pattern, 57.1mm center bore. Factory wheels: 18x8.0J F/R. Reference fitment ranges.
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8.0J F/R |
| Flush Fitment | 18x8.5J at ET30 offset |
| Maximum Aggressive | 19x8.5J at ET25 offset |
Every design below is forged to order, so it can be machined to the ABT VW New Beetle Cabriolet's 5x100 bolt pattern and 57.1 mm center bore, with the width and offset calculated for your setup.

Deep Dish · Gloss Black

Deep Dish · Gloss Black / Gunmetal

Monoblock · Brushed Silver

Replica · Polished Silver

Monoblock · Gloss Bronze

Monoblock · Gloss Black

Replica · White

Monoblock · Gunmetal
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


Convertibles lose some of the structural rigidity a fixed roof provides, which means the suspension and wheels end up doing more of the work to keep the chassis composed. A forged wheel keeps unsprung mass down without sacrificing the strength margin the factory built in — useful on a platform that's already managing extra flex.
The ABT VW New Beetle Cabriolet runs a 5x100 bolt pattern, 57.1mm center bore, and a 18x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x8.5J ET30, which tucks the tire under the fender lip on a stock-height ABT VW New Beetle Cabriolet. Our Maximum Aggressive reference is 19x8.5J ET25 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2003 ABT VW New Beetle Cabriolet (Convertible) uses a 5x100 bolt pattern with a 57.1mm center bore. Factory wheels are 18x8.0J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the ABT VW New Beetle Cabriolet (2003) we drill the 5x100 pattern and cut the centre bore to 57.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact abt spec, or want a wheel built to a custom offset for your ABT VW New Beetle Cabriolet? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.