MMX Design Polished 5-Spoke Forged Wheels
H-Type · Polished
2023 Ford Ranger Wildtrak X Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ford Ranger Wildtrak X wheels? This page gives the 2023 Ford Ranger Wildtrak X bolt pattern (6x139.7), centre bore, factory rim size and the offset range for aftermarket and forged Ford Ranger Wildtrak X rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Ford Ranger Wildtrak X (2023): 6x139.7 bolt pattern, 93.1mm center bore. Factory wheels: 18x8.0J F/R. Reference fitment ranges.
Bolt Pattern6x139.7
Wheel Bolt/Nut1/2\"x20 Nut
Center Bore93.1mm
Wheel Load Rating1000–1400 kg/wheel (Pickup / Light Truck segment reference)
Year2023
CategoryPickup
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8.0J F/R |
| Flush Fitment | 18x9.0J at ET20 offset |
| Maximum Aggressive | 20x9.5J at ET15 offset |
Forged Wheel Designs for the Ford Ranger Wildtrak X
Every design below is forged to order, so it can be machined to the Ford Ranger Wildtrak X's 6x139.7 bolt pattern and 93.1 mm center bore, with the width and offset calculated for your setup.
KG1 Forged Radar Polished Forged Wheels
H-Type · Polished
American Force Polished Multi-Spoke Wheels
H-Type · Polished
DT Forge Pink & Chrome Multi-Spoke Wheels
H-Type · Pink / Chrome
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a truck platform, wheel weight sits right at the unsprung mass budget the suspension engineers already spent on payload and towing capacity. A forged wheel keeps that budget intact — same strength, less rotational inertia — instead of eating into the margin the way a cheap cast aftermarket wheel can.
The Ford Ranger Wildtrak X runs a 6x139.7 bolt pattern, 93.1mm center bore, and a 18x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x9.0J ET20, which tucks the tire under the fender lip on a stock-height Ford Ranger Wildtrak X. Our Maximum Aggressive reference is 20x9.5J ET15 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Ford Ranger Wildtrak X OE Wheel Specs
The 2023 Ford Ranger Wildtrak X (Pickup) uses a 6x139.7 bolt pattern with a 93.1mm center bore. Factory wheels are 18x8.0J F/R.
Why the factory spec works for most owners:
- Preserves the factory-tuned ride and steering feel
- A mainstream size for this segment, keeping tire choice wide and prices reasonable
- Leaves full clearance for the stock brakes and suspension hardware
- Keeps handling predictable and consistent in everyday conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ford Ranger Wildtrak X (2023) we drill the 6x139.7 pattern and cut the centre bore to 93.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x8.0J ET55 → ~6.67″ backspacing
- Flush: 18x9.0J ET20 → ~5.79″ backspacing
- Max: 20x9.5J ET15 → ~5.84″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ford spec, or want a wheel built to a custom offset for your Ford Ranger Wildtrak X? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford Ranger Wildtrak X use?
The 2023 Ford Ranger Wildtrak X uses a 6x139.7 bolt pattern.
How many lug bolts does the Ford Ranger Wildtrak X use?
The Ford Ranger Wildtrak X uses a 6-lug bolt pattern (6x139.7), so you need a 6-lug forged wheel to bolt straight on.
What is the center bore size on the Ford Ranger Wildtrak X?
The Ford Ranger Wildtrak X's center bore is 93.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ford Ranger Wildtrak X?
Factory wheels on the Ford Ranger Wildtrak X are 18x8.0J F/R.
What is the biggest wheel size I can fit on my Ford Ranger Wildtrak X without rubbing?
The most aggressive fitment we recommend without fender work is 20x9.5J at ET15 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ford Ranger Wildtrak X?
For a flush look with minimal to no rubbing, we recommend 18x9.0J at ET20 offset as a starting point on a stock or mildly lowered Ford Ranger Wildtrak X.
Do I need wheel spacers for my Ford Ranger Wildtrak X?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ford Ranger Wildtrak X?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.79" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ford Ranger Wildtrak X?
The Ford Ranger Wildtrak X runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M14x1.5, conical-seat lug nut.
Factory Torque Spec: 135 Nm (100 ft-lb). Ford Ranger (current generation) spec on M14x1.5 studs; earlier Ranger generations used M12x1.5 or M14x2.0 threads, confirm for your exact model year.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.