Fiat OEM-Style Fiat Bright Silver Full-Face Forged Wheels
Monoblock · Bright Silver
2021 Fiat Tipo Cross Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Fiat Tipo Cross wheels? This page gives the 2021 Fiat Tipo Cross bolt pattern (5x98), centre bore, factory rim size and the offset range for aftermarket and forged Fiat Tipo Cross rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2021 Fiat Tipo Cross uses a 5x98 bolt pattern with a 58.1 mm centre bore and M12x1.25 lug bolts. Factory wheels: 17x7.0J, front and rear. For aftermarket wheels, 18x8.0J ET35 sits flush and 19x8.5J ET30 is the most aggressive fit.
Forged wheels for the 2021 Fiat Tipo Cross — drilled 5x98 with a 58.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Fiat Tipo Cross (2021): 5x98 bolt pattern, 58.1mm center bore. Factory wheels: 17x7.0J F/R. Reference fitment ranges.
Bolt Pattern5x98
Wheel Bolt/NutM12x1.25 Bolt
Center Bore58.1mm
Wheel Load Rating800–950 kg/wheel (Crossover segment reference)
Year2021
CategoryCrossover
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x7.0J F/R |
| Flush Fitment | 18x8.0J at ET35 offset |
| Maximum Aggressive | 19x8.5J at ET30 offset |
Forged Wheel Designs for the Fiat Tipo Cross
Every design below is forged to order, so it can be machined to the Fiat Tipo Cross's 5x98 bolt pattern and 58.1 mm center bore, with the width and offset calculated for your setup.
Pastel Blue Full-Face Chrome Lip Forged Wheels
Monoblock · Blue
Alpina-Style Gloss Black 20-Spoke Forged Wheels
Monoblock · Gloss Black
Matte Silver Forged Wheels
Monoblock · Matte Silver
Brushed Silver Full-Face Machined Face Forged Wheels
Monoblock · Brushed Silver
Polished 8-Window Dish Forged Wheels
Off-Road · Polished
Black Rhino-Style Gloss Black 14-Spoke Forged Wheels
Deep Dish · Matte Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Fiat Tipo Cross's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Fiat Tipo Cross runs a 5x98 bolt pattern, 58.1mm center bore, and a 17x7.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x8.0J ET35, which tucks the tire under the fender lip on a stock-height Fiat Tipo Cross. Our Maximum Aggressive reference is 19x8.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Fiat Tipo Cross OE Wheel Specs
The 2021 Fiat Tipo Cross (Crossover) uses a 5x98 bolt pattern with a 58.1mm center bore. Factory wheels are 17x7.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Fiat Tipo Cross (2021) we drill the 5x98 pattern and cut the centre bore to 58.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 17x7.0J ET35 → ~5.38″ backspacing
- Flush: 18x8.0J ET35 → ~5.88″ backspacing
- Max: 19x8.5J ET30 → ~5.93″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Fiat spec, or want a wheel built to a custom offset for your Fiat Tipo Cross? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Fiat Tipo Cross (5x98, 58.1 mm Bore)
In our database, 30 other vehicle entries from 6 makes use exactly the same 5x98 bolt pattern and 58.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x98 is used by 0.5% of the vehicle pages in our English fitment guide (32 of 6,503); 96.9% of those also use a 58.1 mm center bore.
Hub-Centric Rings for a 58.1 mm Center Bore
A wheel with a center bore larger than 58.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 60.1 mm | 60.1 → 58.1 mm |
| 63.4 mm | 63.4 → 58.1 mm |
| 64.1 mm | 64.1 → 58.1 mm |
| 65.1 mm | 65.1 → 58.1 mm |
| 73.1 mm | 73.1 → 58.1 mm |
ANKUSI forged wheels are bored to exactly 58.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Fiat Tipo Cross use?
The 2021 Fiat Tipo Cross uses a 5x98 bolt pattern.
How many lug bolts does the Fiat Tipo Cross use?
The Fiat Tipo Cross uses a 5-lug bolt pattern (5x98), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Fiat Tipo Cross?
The Fiat Tipo Cross's center bore is 58.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Fiat Tipo Cross?
Factory wheels on the Fiat Tipo Cross are 17x7.0J F/R.
What is the biggest wheel size I can fit on my Fiat Tipo Cross without rubbing?
The most aggressive fitment we recommend without fender work is 19x8.5J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Fiat Tipo Cross?
For a flush look with minimal to no rubbing, we recommend 18x8.0J at ET35 offset as a starting point on a stock or mildly lowered Fiat Tipo Cross.
Do I need wheel spacers for my Fiat Tipo Cross?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Fiat Tipo Cross?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Fiat Tipo Cross?
The Fiat Tipo Cross runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 17x7 wheels · 17 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.