2023 Cadillac Escalade-V Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Cadillac Escalade-V wheels? This page gives the 2023 Cadillac Escalade-V bolt pattern (6x139.7), centre bore, factory rim size and the offset range for aftermarket and forged Cadillac Escalade-V rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Cadillac Escalade-V (2023): 6x139.7 bolt pattern, 78.1mm center bore. Factory wheels: 22x9.5J F/R. Reference fitment ranges.
Bolt Pattern6x139.7
Wheel Bolt/NutM14x1.5 Nut
Center Bore78.1mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2023
CategorySUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 22x9.5J F/R |
| Flush Fitment | 23x10.5J at ET15 offset |
| Maximum Aggressive | 24x11.0J at ET10 offset |
Forged Wheel Designs for the Cadillac Escalade-V
Every design below is forged to order, so it can be machined to the Cadillac Escalade-V's 6x139.7 bolt pattern and 78.1 mm center bore, with the width and offset calculated for your setup.
KG1 Forged Radar Polished Forged Wheels
H-Type · Polished
DT Forge Pink & Chrome Multi-Spoke Wheels
H-Type · Pink / Chrome
American Force Polished Multi-Spoke Wheels
H-Type · Polished
MMX Design Polished 5-Spoke Forged Wheels
H-Type · Polished
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Cadillac Escalade-V's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Cadillac Escalade-V runs a 6x139.7 bolt pattern, 78.1mm center bore, and a 22x9.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 23x10.5J ET15, which tucks the tire under the fender lip on a stock-height Cadillac Escalade-V. Our Maximum Aggressive reference is 24x11.0J ET10 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Cadillac Escalade-V OE Wheel Specs
The 2023 Cadillac Escalade-V (SUV) uses a 6x139.7 bolt pattern with a 78.1mm center bore. Factory wheels are 22x9.5J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday drivability
- A commonly used size for this vehicle class, supporting parts and tire availability
- Maintains clearance for the factory suspension and brake components
- Provides stable, predictable handling across normal driving conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Cadillac Escalade-V (2023) we drill the 6x139.7 pattern and cut the centre bore to 78.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 22x9.5J ET22 → ~6.12″ backspacing
- Flush: 23x10.5J ET15 → ~6.34″ backspacing
- Max: 24x11.0J ET10 → ~6.39″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Cadillac spec, or want a wheel built to a custom offset for your Cadillac Escalade-V? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Cadillac Escalade-V use?
The 2023 Cadillac Escalade-V uses a 6x139.7 bolt pattern.
How many lug bolts does the Cadillac Escalade-V use?
The Cadillac Escalade-V uses a 6-lug bolt pattern (6x139.7), so you need a 6-lug forged wheel to bolt straight on.
What is the center bore size on the Cadillac Escalade-V?
The Cadillac Escalade-V's center bore is 78.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Cadillac Escalade-V?
Factory wheels on the Cadillac Escalade-V are 22x9.5J F/R.
What is the biggest wheel size I can fit on my Cadillac Escalade-V without rubbing?
The most aggressive fitment we recommend without fender work is 24x11.0J at ET10 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Cadillac Escalade-V?
For a flush look with minimal to no rubbing, we recommend 23x10.5J at ET15 offset as a starting point on a stock or mildly lowered Cadillac Escalade-V.
Do I need wheel spacers for my Cadillac Escalade-V?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Cadillac Escalade-V?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.34" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Cadillac Escalade-V?
The Cadillac Escalade-V runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.