Honda Prelude Bolt Pattern, Center Bore & Wheel Offset (1992–2001)
Honda Prelude wheel fitment: 5x114.3 bolt pattern, 64.1mm center bore (1997–2001); 4x114.3 bolt pattern, 64.1mm center bore (1992–1994). OE wheel sizes and of
- 5x114.3bolt pattern (PCD), most common
- 64.1 mmcenter bore
- M12x1.5 Nutwheel bolt / nut
- 2 guidesmodel years 1992–2001
Bolt pattern by generation
- 5x114.3, 64.1 mm center bore — 1997–2001 (1 variants)
- 4x114.3, 64.1 mm center bore — 1992–1994 (1 variants)
Honda Prelude wheel specs by year and trim
| Year | Model / trim | Bolt pattern | Center bore | OE wheel |
|---|---|---|---|---|
| 2001 | Honda Prelude | 5x114.3 | 64.1 mm | 16x6.5J |
| 1994 | Honda Prelude Si | 4x114.3 | 64.1 mm | 15x6.5J |
Factory wheel sizes on the Honda Prelude
Across the 2 Honda Prelude trims with a documented factory wheel, the OE diameter is 15-16 inch, width 6.5J. A forged wheel that keeps the bolt pattern and hub bore of your generation (see the table above) and matches the factory offset listed on the model page bolts on without spacers or hub rings. Going one inch up in diameter with a lower-profile tyre keeps the rolling circumference inside the usual 1.5% tolerance; every extra 0.5J of width moves the outer lip about 6 mm outward at the same offset, and each 5 mm less offset moves the whole wheel 5 mm outward.
Forged wheels for the Honda Prelude (5x114.3)
Shop all Honda Prelude forged wheels →
Get a quote for Honda Prelude wheels
Vehicles With the Same Hub as the Honda Prelude (5x114.3, 64.1 mm Bore)
In our database, 22 other vehicle entries from 6 makes use exactly the same 5x114.3 bolt pattern and 64.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle entries in our database (1,300 of 6,503); 2.8% of those also use a 64.1 mm center bore.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 16x6.5J | ET55 | 5.92 in (150 mm) | — | — |
| Flush | 18x8.5J | ET32 | 6.01 in (153 mm) | +2 mm | +48 mm |
| Maximum | 17x9J | ET30 | 6.18 in (157 mm) | +7 mm | +57 mm |
Hub-Centric Rings for a 64.1 mm Center Bore
A wheel with a center bore larger than 64.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 65.1 mm | 65.1 → 64.1 mm |
| 66.1 mm | 66.1 → 64.1 mm |
| 66.6 mm | 66.6 → 64.1 mm |
| 67.1 mm | 67.1 → 64.1 mm |
| 73.1 mm | 73.1 → 64.1 mm |
ANKUSI forged wheels are bored to exactly 64.1 mm for this vehicle, so no ring is needed.
Sources and Last Update
Bolt pattern and center bore were checked against at least two independent fitment references before publication.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
FAQ
What is the bolt pattern on a Honda Prelude?
The Honda Prelude uses a 5x114.3 bolt pattern on most variants we cover with a 64.1mm center bore. Other generations use 4x114.3 / 64.1mm (1992–1994). Always check the exact year and trim before ordering.
What is the Honda Prelude center bore?
The hub-centric center bore is 64.1 mm on the most common generation; see the table for variants. Aftermarket wheels should match this bore or use hub-centric rings so the hub, not the bolts, carries the load.
Do all Honda Prelude years share the same wheel fitment?
No. The bolt pattern or center bore changed between generations, so wheels are not interchangeable across all years. Use the year-by-year table on this page to pick the right specification.
Which forged wheels fit the Honda Prelude?
Any wheel drilled 5x114.3 with a 64.1mm hub bore in the offset range shown on the model guide. ANKUSI forges wheels to order for this exact specification, in 14–24 inch diameters, so no adapters or hub rings are needed.