Gloss White Lettered Smoothie Forged Wheels
Monoblock · Gloss White
2005 Porsche 911 Turbo S Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Porsche 911 Turbo S wheels? This page gives the 2005 Porsche 911 Turbo S bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Porsche 911 Turbo S rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2005 Porsche 911 Turbo S uses a 5x130 bolt pattern with a 71.6 mm centre bore and M14x1.5 lug bolts. Factory wheels: F: 18x8J R: 18x11J. For aftermarket wheels, 19x8.5J ET53 front / 19x11J ET40 rear sits flush and 19x8.5J ET40 front / 19x11.5J ET30 rear is the most aggressive fit.
Forged wheels for the 2005 Porsche 911 Turbo S — drilled 5x130 with a 71.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Porsche 911 Turbo S (2005): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: F: 18x8J R: 18x11J. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Caliper TypeFixed 6-piston front caliper (OEM, Porsche Turbo)
Year2005
CategorySupercar
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 18x8J R: 18x11J |
| Flush Fitment | F 19x8.5J ET53 / R 19x11J ET40 |
| Maximum Aggressive | F 19x8.5J ET40 / R 19x11.5J ET30 |
Forged Wheel Designs for the Porsche 911 Turbo S
Every design below is forged to order, so it can be machined to the Porsche 911 Turbo S's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
BBS-Style Gold Mesh Forged Wheels
2-Piece · Custom Finish
Transparent Black Forged Wheels
Monoblock · Transparent Black
Porsche OEM-Style Gunmetal 5-Spoke Forged Wheels
Monoblock · Gunmetal
Silver Lattice Mesh Forged Wheels
Monoblock · Silver
Copper Steelie Dish Forged Wheels
Monoblock · Copper
Forgeline-Style Matte Black 10-Spoke Deep Dish 2-Piece Forged Wheels
2-Piece · Matte Black
Bronze 5 V-Spoke Forged Wheels
Monoblock · Bronze
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Every gram of rotational mass on a supercar fights the acceleration, braking, and rotational inertia numbers the factory spent enormous engineering effort achieving. A forged wheel for the Porsche 911 Turbo S holds the OE strength rating at meaningfully less weight, which is a real, measurable performance gain rather than a cosmetic one.
The Porsche 911 Turbo S runs a 5x130 bolt pattern, 71.6mm center bore, and a F: 18x8J wheel from the factory. Our Flush Fitment reference is F 19x8.5J ET53 / R 19x11J ET40, which tucks the tire under the fender lip on a stock-height Porsche 911 Turbo S. Our Maximum Aggressive reference is F 19x8.5J ET40 / R 19x11.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Porsche 911 Turbo S OE Wheel Specs
The 2005 Porsche 911 Turbo S (Supercar) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are F: 18x8J R: 18x11J.
Why the factory spec works for most owners:
- Balances ride comfort with everyday drivability
- A commonly used size for this vehicle class, supporting parts and tire availability
- Maintains clearance for the factory suspension and brake components
- Provides stable, predictable handling across normal driving conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche 911 Turbo S (2005) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Real-World Fitment Notes
HRE / forged staggered 19s; Turbo S shares 996 Turbo widebody shell 996 Turbo S widebody (last of 996); same-platform 996 Turbo verified (6SpeedOnline) F 18x8J ET50 / R 18x11J ET45 (hollow-spoke), 5x130, CB71.6
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 18x8J ET50 → ~6.47″ F backspacing, R 18x11J ET45 → ~7.77″ R backspacing
- Flush: F 19x8.5J ET53 → ~6.84″ F backspacing, R 19x11J ET40 → ~7.57″ R backspacing
- Max: F 19x8.5J ET40 → ~6.32″ F backspacing, R 19x11.5J ET30 → ~7.43″ R backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche 911 Turbo S? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Porsche 911 Turbo S: Specs by Model Year
Vehicles With the Same Hub as the Porsche 911 Turbo S (5x130, 71.6 mm Bore)
In our database, 293 other vehicle entries from 10 makes use exactly the same 5x130 bolt pattern and 71.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x130 is used by 5.8% of the vehicle pages in our English fitment guide (375 of 6,503); 78.7% of those also use a 71.6 mm center bore.
Hub-Centric Rings for a 71.6 mm Center Bore
A wheel with a center bore larger than 71.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 72.6 mm | 72.6 → 71.6 mm |
| 73.1 mm | 73.1 → 71.6 mm |
| 74.1 mm | 74.1 → 71.6 mm |
| 76.1 mm | 76.1 → 71.6 mm |
ANKUSI forged wheels are bored to exactly 71.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Porsche 911 Turbo S use?
The 2005 Porsche 911 Turbo S uses a 5x130 bolt pattern.
How many lug bolts does the Porsche 911 Turbo S use?
The Porsche 911 Turbo S uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Porsche 911 Turbo S?
The Porsche 911 Turbo S's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Porsche 911 Turbo S?
Factory wheels on the Porsche 911 Turbo S are F: 18x8J R: 18x11J.
What is the biggest wheel size I can fit on my Porsche 911 Turbo S without rubbing?
The most aggressive fitment we recommend without fender work is F 19x8.5J ET40 / R 19x11.5J ET30. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Porsche 911 Turbo S?
For a flush look with minimal to no rubbing, we recommend F 19x8.5J ET53 / R 19x11J ET40 as a starting point on a stock or mildly lowered Porsche 911 Turbo S.
Do I need wheel spacers for my Porsche 911 Turbo S?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Porsche 911 Turbo S?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.84" backspacing up front and 7.57" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Porsche 911 Turbo S?
Yes — the Porsche 911 Turbo S's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x8 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.