Matte Silver Fan Spoke Directional Milled Forged Wheels
Monoblock · Matte Silver
1992 Porsche 911 Turbo S 3.3 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Porsche 911 Turbo S 3.3 wheels? This page gives the 1992 Porsche 911 Turbo S 3.3 bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Porsche 911 Turbo S 3.3 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Porsche 911 Turbo S 3.3 (1992): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: F: 18x8J R: 18x10J. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Caliper TypeFixed 6-piston front caliper (OEM, Porsche Turbo)
Year1992
CategorySupercar
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 18x8J R: 18x10J |
| Flush Fitment | F 18x8.5J ET44 / R 18x10J ET36 |
| Maximum Aggressive | F 18x8.5J ET44 / R 18x10J ET36 |
Forged Wheel Designs for the Porsche 911 Turbo S 3.3
Every design below is forged to order, so it can be machined to the Porsche 911 Turbo S 3.3's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
Black / Copper Concave Forged Wheels
Concave · Black / Copper
Porsche OEM-Style Transparent Gold 5 Y-Spoke Forged Wheels
Monoblock · Transparent Gold
CF Gunmetal 2-Piece Deep Lip Forged Wheels
2-Piece · Gunmetal
Anrky-Style Mirror Polished 8-Spoke Forged Wheels
Monoblock · Mirror Polished
Mirror Polished 4-Petal Forged Wheels
Monoblock · Matte Silver
HRE Performance P101-Style Brushed Silver 5 Y-Spoke Forged Wheels
Replica · Brushed Silver
Gold Mesh Forged Wheels
Monoblock · Gold
See all Porsche 911 wheel designs Porsche OEM-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
At this power level the wheel is a safety component. Offsets are tight, brake packages are enormous, and there is very little room between the caliper and the barrel. A forged wheel built to the correct spec is not a cosmetic upgrade here - it is the only sensible way to change the look without compromising clearance or strength.
The Porsche 911 Turbo S 3.3 runs a 5x130 fitment, 71.6mm center bore, and a F: 18x8J wheel from the factory. Our Flush Fitment reference is F 18x8.5J ET44 / R 18x10J ET36, which tucks the tire under the fender lip on a stock-height Porsche 911 Turbo S 3.3. Our Maximum Aggressive reference is F 18x8.5J ET44 / R 18x10J ET36 - the verified data does not support going wider than the flush spec on this chassis.
Porsche 911 Turbo S 3.3 OE Wheel Specs
The 1992 Porsche 911 Turbo S 3.3 (Supercar) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are F: 18x8J R: 18x10J.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche 911 Turbo S 3.3 (1992) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Real-World Fitment Notes
964 Turbo 3.3 runs 18in Speedline, APEX, or HRE 3-piece; deep-concave rears popular for flared body 5x130 / 71.6 CB; data verified against 993/964 Turbo widebody (APEX/WheelPrice fitment guides)
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 18x8J ET52 → ~6.55″ F backspacing, R 18x10J ET61 → ~7.9″ R backspacing
- Flush: F 18x8.5J ET44 → ~6.48″ F backspacing, R 18x10J ET36 → ~6.92″ R backspacing
- Max: F 18x8.5J ET44 → ~6.48″ F backspacing, R 18x10J ET36 → ~6.92″ R backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche 911 Turbo S 3.3? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Porsche 911 Turbo S 3.3 use?
The 1992 Porsche 911 Turbo S 3.3 uses a 5x130 bolt pattern.
How many lug bolts does the Porsche 911 Turbo S 3.3 use?
The Porsche 911 Turbo S 3.3 uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Porsche 911 Turbo S 3.3?
The Porsche 911 Turbo S 3.3's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Porsche 911 Turbo S 3.3?
Factory wheels on the Porsche 911 Turbo S 3.3 are F: 18x8J R: 18x10J.
What is the biggest wheel size I can fit on my Porsche 911 Turbo S 3.3 without rubbing?
The most aggressive fitment we recommend without fender work is F 18x8.5J ET44 / R 18x10J ET36. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Porsche 911 Turbo S 3.3?
For a flush look with minimal to no rubbing, we recommend F 18x8.5J ET44 / R 18x10J ET36 as a starting point on a stock or mildly lowered Porsche 911 Turbo S 3.3.
Do I need wheel spacers for my Porsche 911 Turbo S 3.3?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Porsche 911 Turbo S 3.3?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.48" backspacing up front and 6.92" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Porsche 911 Turbo S 3.3?
Yes — the Porsche 911 Turbo S 3.3's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.