Datsun Wheel Fitment Guide

6 fitment guides for Datsun, covering 2014 to 2022, spanning 4x98 and 4x100 bolt patterns. Browse the full list below, then open a model for bolt pattern, center bore, OE offset, flush and max wheel sizes, and offset/backspacing conversions.

Run a Datsun club, forum or blog? Add our free bolt pattern and center bore lookup to your site, set to open on Datsun only. Get the free embed code →

Datsun models: bolt pattern by model

GO

Datsun Bolt Pattern & Center Bore Notes

Based on the 6 Datsun fitment guides we cover, we have documented 2 distinct bolt pattern / center bore combinations across different Datsun platforms and model years:

  • 4x100 bolt pattern, 60.1mm center bore — 4 models we cover, spanning 2014–2022.
  • 4x98 bolt pattern, 58.6mm center bore — 2 models we cover, spanning 2015.

Do not mix platforms: a wheel forged for one Datsun bolt pattern / center bore combination will not hub-center correctly on a different one, even if the diameter looks right. Always confirm your exact model and year against the bolt pattern and center bore listed on that model page below before ordering — or send us your VIN or trim level and we will confirm it for you.

Offset and backspacing recommendations vary by trim even within the same bolt pattern, mainly due to differences in brake caliper size and suspension geometry between base and performance trims. Every ANKUSI wheel is forged to your exact target offset, so send us your Datsun model, year, and trim and we will confirm the correct spec before production — no guessing required.

How to check the bolt pattern on your Datsun

The most common Datsun fitment in our guide is 4x100 with a 60.1 mm center bore (4 of 6 model years we cover).

  1. Read the stamping on the back of an original wheel: size, offset (ET) and bolt pattern are usually cast into a spoke or the hub pad.
  2. No stamping? Measure center-to-center between two adjacent lug holes. For 4x100 that distance is 70.7 mm (PCD × sin(180° / 4)). A 2 mm difference already means a different bolt pattern.
  3. Match generation and year on the model pages below — the same nameplate can change bolt pattern or center bore between generations.

Changing width or offset? Check how far the wheel moves in or out with our offset & backspacing calculator.

Forged Wheels for Datsun

Forged-to-order wheel designs matched to Datsun bolt patterns. Every set is machined to your exact model, offset and center bore.

Vehicles Using 4x100 With a 60.1 mm Center Bore

In our database, 148 other vehicle entries from 9 makes use exactly the same 4x100 bolt pattern and 60.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.

4x100 is used by 6.9% of the vehicle pages in our English fitment guide (451 of 6,503); 33.3% of those also use a 60.1 mm center bore.

Hub-Centric Rings for a 60.1 mm Center Bore

A wheel with a center bore larger than 60.1 mm needs a hub-centric ring. The most common combinations:

Wheel boreRing size
63.4 mm63.4 → 60.1 mm
64.1 mm64.1 → 60.1 mm
65.1 mm65.1 → 60.1 mm
66.1 mm66.1 → 60.1 mm
73.1 mm73.1 → 60.1 mm

ANKUSI forged wheels are bored to exactly 60.1 mm for this vehicle, so no ring is needed.

Sources and Last Update

Bolt pattern and center bore were checked against at least two independent fitment references before publication.

This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).

Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.

← Back to the full Fitment Guide · Browse forged wheels

Contact WhatsApp Get a Quote