Fitting Honda Passport wheels? This page gives the 2026 Honda Passport bolt pattern (5x120), centre bore, factory rim size and the offset range for aftermarket and forged Honda Passport rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2026 Honda Passport uses a 5x120 bolt pattern with a 64.1 mm centre bore and M14x1.5 lug thread. Factory wheels: 18x8J at ET55, front and rear. For aftermarket wheels, 18x8.5J ET50 sits flush and 19x9J ET45 is the most aggressive fit.
Forged wheels for the 2026 Honda Passport — drilled 5x120 with a 64.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in about 25 days.
Honda Passport (2026): 5x120 bolt pattern, 64.1mm center bore. Factory wheels: 18x8J at ET55 offset. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed October 19, 2026. How we verify
Built to order by ANKUSI — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8J at ET55, front and rear |
| Flush Fitment | F 18x8.5J ET50 / R 18x8.5J ET50 |
| Maximum Aggressive | F 19x9J ET45 / R 19x9J ET45 |
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
On a vehicle this heavy, the wheel is a structural part before it is a styling part - it carries the load, the brake heat and the cornering forces all at once. A forged wheel buys back unsprung weight without giving up the load rating an SUV actually needs, which is the one number most cast aftermarket wheels quietly fall short on.
The Honda Passport runs a 5x120 bolt pattern, 64.1mm center bore, and a 18x8J ET55 wheel front and rear from the factory. Our Flush Fitment reference is F 18x8.5J ET50 / R 18x8.5J ET50, which tucks the tire under the fender lip on a stock-height Honda Passport. Our Maximum Aggressive reference is F 19x9J ET45 / R 19x9J ET45 - beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2026 Honda Passport (SUV) uses a 5x120 bolt pattern with a 64.1mm center bore. Factory wheels are 18x8J at ET55, front and rear.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Honda Passport (2026) we drill the 5x120 pattern and cut the centre bore to 64.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
For a flush look with minimal rubbing, F 18x8.5J ET50 / R 18x8.5J ET50 is the recommended starting point on a stock or mildly lowered Honda Passport.
F 19x9J ET45 / R 19x9J ET45 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
Fourth-generation Passport (YF9, 2026 model year on). RTL runs 265/60R18 and TrailSport runs 275/60R18 all-terrain tires on the same 18x8J ET55 wheel.
Recommended setup: F 18x8.0J ET55 / R 18x8.0J ET55 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
Recommended setup: F 18x8.5J ET53 / R 18x8.5J ET53 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
Recommended setup: F 18x8.5J ET50 / R 18x8.5J ET50 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
Recommended setup: F 19x9.0J ET48 / R 19x9.0J ET48 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
Recommended setup: F 19x9.0J ET45 / R 19x9.0J ET45 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | F 18x8.0J ET55 / R 18x8.0J ET55 | F 18x8.5J ET53 / R 18x8.5J ET53 | F 18x8.5J ET50 / R 18x8.5J ET50 | F 19x9.0J ET48 / R 19x9.0J ET48 | F 19x9.0J ET45 / R 19x9.0J ET45 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: F 18x8.0J ET55 / R 18x8.0J ET55
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: F 18x8.5J ET50 / R 18x8.5J ET50
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: F 19x9.0J ET45 / R 19x9.0J ET45
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Honda spec, or want a wheel built to a custom offset for your Honda Passport? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x120 pattern and the 64.1mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose.
Designs we already tool for the 5x120 pattern — each one is re-cut to your sizes and offsets:
BBS RE-V7-Style Gunmetal 7 Y-Spoke Forged Wheels – Toyota GR86 / Honda Civic Type R Fitment (5-Lug)
RAYS VOLK RACING TE37-Style S PLUS Space Gray 6-Spoke Forged Wheels – Honda Civic Type R Fitment (18-20in, 5x120)
Honda OEM-Style Metallic Gray Directional Milled Forged Wheels – Honda Civic / Accord Fitment (5-Lug)
Belak-Style Black Machined Beadlock Milled-Ring Mesh Forged Drag Racing Wheels – Honda Civic / Ford Mustang Fitment (5-Lug)Every design below is forged to order, so it can be machined to the Honda Passport's 5x120 bolt pattern and 64.1 mm center bore, with the width and offset calculated for your setup.
BBS-Style forged wheels featuring the RI-D-style gloss bronze 5 Y-spoke design, forged to order at ANKUSI's Guangzhou plant. Bolt pattern, centre bore, diameter, width and offset are machined for your exact vehicle — this listing covers 5-lug applications.
Honda Accord / Civic Fitment · 5-Lug
Honda Civic / Accord Fitment · 5-Lug
Honda Civic / Accord Fitment · 5-Lug
Gloss Black 5 Split-Spoke · 5-Lug
Brushed Silver 5-Spoke · 18-20in, 5x120
BBS-Style forged wheels featuring the RI-D-style bronze gold 5 Y-spoke design, forged to order at ANKUSI's Guangzhou plant. Bolt pattern, centre bore, diameter, width and offset are machined for your exact vehicle — this listing covers 5-lug applications.
Advan-Style forged wheels featuring the bright gray 6-spoke deep lip design, forged to order at ANKUSI's Guangzhou plant. Bolt pattern, centre bore, diameter, width and offset are machined for your exact vehicle — this listing covers 5-lug applications.
Bolt pattern and center bore on this page were cross-checked against at least two independent sources before publication. Last reviewed 2026-10-19. Spotted an error? Email info@ankusi.com and we will verify and correct it.