
Black / Machined 4-Spoke Forged Wheels
Monoblock · Black Machined
Fitting Nissan Versa Hatchback wheels? This page gives the 2007 Nissan Versa Hatchback bolt pattern (4x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Nissan Versa Hatchback rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Nissan Versa — styles, sizes & factory quote →
Nissan Versa Hatchback (2007): 4x114.3 bolt pattern, 66.1mm center bore, OE 15x5.5J ET40. Forged wheel fitment specs from ANKUSI.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 15x5.5J ET40 |
| Flush Fitment | 16x7J at ET35 offset |
Every design below is forged to order, so it can be machined to the Nissan Versa Hatchback's 4x114.3 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.

Monoblock · Black Machined

Monoblock · Bronze Gold

Monoblock · Silver

Monoblock · Bright Silver

Monoblock · Matte Bronze

Monoblock · Matte Silver

Deep Dish · Gunmetal

Monoblock · Gloss White
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


On a compact performance platform, every pound of rotational mass fights the car's natural agility. A forged wheel keeps strength at the factory-rated level while cutting that rotational weight, which is where the driving-feel improvement actually comes from.
The Nissan Versa Hatchback ships from the factory on a 4x114.3 bolt pattern with a 66.1mm center bore and a 15x5.5J ET40 wheel. Our flush reference for the Nissan Versa Hatchback is 16x7J ET35.; our maximum aggressive reference is 17x7.5J ET30. — beyond that, expect clearance issues against the fender liner without further modification.
The Nissan Versa Hatchback ships from the factory on 4x114.3 bolt pattern wheels with a 66.1mm center bore. The stock wheel size is 15x5.5J ET40, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Nissan Versa Hatchback (2007) we drill the 4x114.3 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.
Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your Nissan Versa Hatchback.
Thread & Fastener: M12x1.25, conical-seat lug nut.
Factory Torque Spec: 103-122 Nm (76-90 ft-lb). Range covers most Nissan passenger cars and crossovers on M12x1.25 studs.
TPMS: Vehicles built before the 2008 model year were not federally required to carry factory TPMS in the US, though many manufacturers adopted it earlier; verify whether your specific build has TPMS before ordering sensor-compatible wheels.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.