XPeng OEM-Style Satin Black Slotted Disc Forged Wheels
Monoblock · Satin Black
2025 XPeng G7 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting XPeng G7 wheels? This page gives the 2025 XPeng G7 bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged XPeng G7 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2025 XPeng G7 uses a 5x112 bolt pattern with a 60.1 mm centre bore. Factory wheels: 18x7.5J, front and rear.
Forged wheels for the 2025 XPeng G7 — drilled 5x112 with a 60.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
XPeng G7 (2025): 5x112 bolt pattern, 60.1mm center bore. Factory wheels: 18x7.5J F/R. Flush and max fitment confirmed on request.
Bolt Pattern5x112
Wheel Bolt/NutNut
Center Bore60.1mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Caliper TypeFactory disc brakes, all four corners (OEM)
Year2025
CategorySUV
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Forged Wheel Designs for the XPeng G7
Every design below is forged to order, so it can be machined to the XPeng G7's 5x112 bolt pattern and 60.1 mm center bore, with the width and offset calculated for your setup.
Matte Silver Petal Cross Split-Spoke Side-Milled Forged Wheels
Monoblock · Matte Silver
Audi RS5 Sedan Forged Wheels
Monoblock
Xpeng OEM-Style Polished Slotted Disc Forged Wheels
Replica · Polished
WF Gloss Black 10-Spoke Forged Wheels
Replica · Gloss Black
APEX-Style Brushed Silver 10-Spoke Forged Wheels
Monoblock · Brushed Silver
Gloss Black Mesh 2-Piece Polished Deep Lip Forged Wheels
2-Piece · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a vehicle this heavy, the wheel is a structural part before it is a styling part - it carries the load, the brake heat and the cornering forces all at once. A forged wheel buys back unsprung weight without giving up the load rating an SUV actually needs, which is the one number most cast aftermarket wheels quietly fall short on.
We publish the factory specification for the XPeng G7 below. We have not yet been able to verify aftermarket flush or maximum-aggressive offsets for this exact variant against a source we trust, so we are not listing any - an invented offset is worse than no offset when a wheel has to clear a caliper.
XPeng G7 OE Wheel Specs
The 2025 XPeng G7 (SUV) uses a 5x112 bolt pattern with a 60.1mm center bore. Factory wheels are 18x7.5J F/R.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the XPeng G7 (2025) we drill the 5x112 pattern and cut the centre bore to 60.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Aftermarket Fitment: Confirmed on Request
Published aftermarket fitment for this exact variant is still thin, so we have not committed to a flush or maximum-aggressive figure. Our engineering team is still collecting verified data for this variant. In the meantime the factory specification above is accurate and is the safe reference point for ordering.
What we do know: Generation I, model years 2025-2027. Verified against two independent fitment references.
Need a wheel for this car now? Contact ANKUSI with your target diameter, width and offset and our engineers will confirm the correct forged spec against your brake package before anything is cut. You can also use our Offset & Backspacing Calculator to work through the numbers yourself.
XPeng G7: Specs by Model Year
| Year | Bolt pattern | Center bore | Factory wheel |
|---|---|---|---|
| 2025 | 5x112 | 60.1 mm | 18x7.5J |
| 2027 | 5x112 | 60.1 mm | 18x7.5J |
Bolt pattern and center bore stay the same across all 2 model years in our database (2025–2027).
Vehicles With the Same Hub as the XPeng G7 (5x112, 60.1 mm Bore)
In our database, 3 other XPeng entries use exactly the same 5x112 bolt pattern and 60.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 0.3% of those also use a 60.1 mm center bore.
Hub-Centric Rings for a 60.1 mm Center Bore
A wheel with a center bore larger than 60.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 63.4 mm | 63.4 → 60.1 mm |
| 64.1 mm | 64.1 → 60.1 mm |
| 65.1 mm | 65.1 → 60.1 mm |
| 66.1 mm | 66.1 → 60.1 mm |
| 73.1 mm | 73.1 → 60.1 mm |
ANKUSI forged wheels are bored to exactly 60.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the XPeng G7 use?
The 2025 XPeng G7 uses a 5x112 bolt pattern.
How many lug bolts does the XPeng G7 use?
The XPeng G7 uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the XPeng G7?
The XPeng G7's center bore is 60.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the XPeng G7?
Factory wheels on the XPeng G7 are 18x7.5J F/R.
Do I need wheel spacers for my XPeng G7?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my XPeng G7?
The XPeng G7 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Bolt pattern and center bore come from published fitment references; a second independent check is still pending (see the data check note above).
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x7.5 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-10-10. Spotted an error? Email info@ankusi.com and we will verify and correct it.