Rays-Style Gunmetal 6-Spoke Forged Wheels
Nissan 370Z / Toyota GR86 Fitment · 5-Lug
2011 Nissan Juke Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Nissan Juke wheels? This page gives the 2011 Nissan Juke bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Nissan Juke rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Nissan Juke (2011): 5x114.3 bolt pattern, 66.1mm center bore. Factory wheels: 17x7.0J at ET47 offset, front and rear. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.25 Nut
Center Bore66.1mm
Wheel Load Rating800–950 kg/wheel (Crossover segment reference)
Year2011
CategoryCompact Crossover
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x7.0J F/R |
| Flush Fitment | 18x8.0J at ET35 offset |
| Maximum Aggressive | 19x8.5J at ET30 offset |
Forged wheels for the Nissan JukeMachined to the 5x114.3 bolt pattern and 66.1 mm bore · 14–24 inch · offset calculated for your car · 3D drawing before production
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Nissan Juke runs a 5x114.3 bolt pattern, 66.1mm center bore, and a 17x7.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x8.0J ET35, which tucks the tire under the fender lip on a stock-height Nissan Juke. Our Maximum Aggressive reference is 19x8.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Nissan Juke OE Wheel Specs
The 2011 Nissan Juke (Compact Crossover) uses a 5x114.3 bolt pattern with a 66.1mm center bore. Factory wheels are 17x7.0J F/R.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Nissan Juke (2011) we drill the 5x114.3 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look, F/R 18x8.0J ET35 is a commonly used starting point — clearance must be verified on a stock or mildly lowered Nissan Juke.
Maximum Aggressive Fitment
F/R 19x8.5J ET30 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style 17x7.0J ET47
Recommended setup: 17x7.0J ET47 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,200-1,500 (wheels + tires + install)
B Comfortable Upgrade 18x7.5J ET41
Recommended setup: 18x7.5J ET41 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 18x8.0J ET35
Recommended setup: 18x8.0J ET35 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 19x8.5J ET33
Recommended setup: 19x8.5J ET33 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 19x8.5J ET30
Recommended setup: 19x8.5J ET30 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 17x7.0J ET47 | 18x7.5J ET41 | 18x8.0J ET35 | 19x8.5J ET33 | 19x8.5J ET30 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $1,200-1,500 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 17x7.0J ET47
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 18x8.0J ET35
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 19x8.5J ET30
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
1
What's your primary use? Daily commuting → Tier A/B. Weekend street driving → Tier B/C. Show or occasional track use → Tier D/E.
2
What's your budget? Under $800 → Tier A. $800-3,400 → Tier B/C. $3,400+ → Tier D/E.
3
How much does fuel economy matter? Very important → Tier A. Somewhat important → Tier B/C. Not a priority → Tier D/E.
4
Still unsure? Tier C (Balanced / Flush Fit) is the default choice for most Nissan Juke owners.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 17x7.0J ET47 → ~5.85″ backspacing
- Flush: 18x8.0J ET35 → ~5.88″ backspacing
- Max: 19x8.5J ET30 → ~5.93″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Nissan spec, or want a wheel built to a custom offset for your Nissan Juke? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Custom Forged Wheels for the Nissan Juke (2011)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x114.3 pattern and the 66.1mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose — most Nissan orders on this platform land somewhere between the 18x8.0J ET35 flush setup and the 19x8.5J ET30 aggressive setup referenced above.
Designs we already tool for the 5x114.3 pattern — each one is re-cut to your sizes and offsets:
Rays-Style Matte Black 6-Spoke Deep Lip Racing Forged Wheels – Nissan 370Z / Toyota GR86 Fitment (5-Lug)
Rays-Style Gloss Black 5 Y-Spoke Pinstripe Lip Forged Wheels – Nissan GT-R / Toyota GR Supra Fitment (5-Lug)
Honda Civic / Mazda MX-5 Forged Wheels – Polished Silver 6-Spoke Deep Lip (5-Lug)
Forthing OEM-Style Bright Silver Full-Face Forged Wheels – Forthing T5 EVO Fitment (5-Lug)Frequently Asked Questions
What bolt pattern (PCD) does the Nissan Juke use?
The 2011 Nissan Juke uses a 5x114.3 bolt pattern.
How many lug bolts does the Nissan Juke use?
The Nissan Juke uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Nissan Juke?
The Nissan Juke's center bore is 66.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Nissan Juke?
Factory wheels on the Nissan Juke are 17x7.0J F/R.
What is the biggest wheel size I can fit on my Nissan Juke without rubbing?
The most aggressive fitment we recommend without fender work is 19x8.5J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Nissan Juke?
For a flush look with minimal to no rubbing, we recommend 18x8.0J at ET35 offset as a starting point on a stock or mildly lowered Nissan Juke.
Do I need wheel spacers for my Nissan Juke?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Nissan Juke?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Nissan Juke?
The Nissan Juke runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Forged Wheel Designs for the Nissan Juke
Every design below is forged to order, so it can be machined to the Nissan Juke's 5x114.3 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.
Work Emotion Custom Finish Petal Machined Face Forged Wheels
Nissan 370Z / Subaru BRZ Fitment · 5-Lug
Vossen HF-7-Style Brushed Silver Multi-Spoke Forged Wheels
Tesla Model Y / Tesla Model 3 Fitment · 5-Lug
Honda Civic / Mazda MX-5 Forged Wheels
Polished Silver 6-Spoke Deep Lip · 5-Lug
Nissan 370Z / Toyota GR86 Forged Wheels
Metallic Gray / Gray 7 Y-Spoke
CCW-Style Brushed Silver Mesh Polished-Lip Forged Wheels
Audi R8 / 911 Fitment · 5-Lug
Nissan OEM-Style Gloss Black Custom Forged Wheels
Nissan GT-R / 370Z Fitment · 5-Lug
Audi R8 / 911 Forged Wheels
Chrome 7 Split-Spoke Deep Dish 2-Piece · 5-Lug
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.25, conical-seat lug nut.
Factory Torque Spec: 103-122 Nm (76-90 ft-lb). Range covers most Nissan passenger cars and crossovers on M12x1.25 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.