Morgan Plus Six (2023) Wheel Fitment
Morgan Plus Six (2023): 5x114.3 bolt pattern, 67.1mm center bore, OE F 18x8J ET35 / R 18x9J ET35. Forged wheel fitment specs from ANKUSI.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 19x8.5J ET28 / R 19x9.5J ET35 |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Most of the engineering value in a forged wheel over a cast one shows up in rotational mass, not outright strength — both can meet the same load rating, but the forged piece gets there lighter. On a sedan platform tuned for everyday balance, that weight saving is felt directly in steering response and ride quality.
The Morgan Plus Six ships from the factory on a 5x114.3 bolt pattern with a 67.1mm center bore and a F 18x8J ET35 / R 18x9J ET35 wheel. Our flush reference for the Morgan Plus Six is F 19x8.5J ET28 / R 19x9.5J ET35.; our maximum aggressive reference is F 20x9J ET25 / R 20x10J ET30. — beyond that, expect clearance issues against the fender liner without further modification.
Morgan Plus Six OE Wheel Specs
The Morgan Plus Six ships from the factory on 5x114.3 bolt pattern wheels with a 67.1mm center bore. The stock wheel size is F 18x8J ET35 / R 18x9J ET35, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
Flush Fitment
For a flush look without any body modification, most Morgan Plus Six owners run F 19x8.5J ET28 / R 19x9.5J ET35. This setup tucks the wheel face closer to the fender lip while staying within safe load and clearance limits.
Maximum Aggressive Fitment
Owners chasing a more aggressive stance push to F 20x9J ET25 / R 20x10J ET30. Nitron adjustable coilovers; 19-inch forged alloy wheels; AP Racing performance brakes; Michelin Pilot Sport 4S (F: 225/40 R19, R: 255/35 R19). Note: CX-generation flagship powered by a BMW 3.0L turbocharged inline-6 engine (335 hp). Clearance should be verified before ordering, especially on lowered cars.
5-Tier Configuration Options
A – Factory-Style: 18x8J ET35
Recommended setup: Factory-matched forged replacement
Economy impact: None
Best for: Daily drivers, warranty-conscious owners
Appearance 5/10 | Comfort 10/10 | Install difficulty ★☆☆☆
Estimated cost range: $$ (OE replacement)
B – Comfortable Upgrade: F 18.5x8.5J ET32 / R 18.5x9.5J ET35
Recommended setup: Direct bolt-on, factory suspension
Economy impact: Minimal
Best for: Owners who want a mild upgrade with no compromise
Appearance 6/10 | Comfort 9/10 | Install difficulty ★☆☆☆
Estimated cost range: $$ - $$$
C – Balanced / Flush Fit: F 19x8.5J ET28 / R 19x9.5J ET35
Recommended setup: Flush forged wheels, stock or mild lowering
Economy impact: Slight increase
Best for: Enthusiasts wanting a flush look daily
Appearance 8/10 | Comfort 7/10 | Install difficulty ★★☆☆
Estimated cost range: $$$
D – Aggressive: F 19.5x9J ET27 / R 19.5x10J ET33
Recommended setup: Wider forged wheels, coilovers or lowering springs
Economy impact: Noticeable increase
Best for: Show-and-drive builds
Appearance 9/10 | Comfort 5/10 | Install difficulty ★★★☆
Estimated cost range: $$$$
E – Max Aggressive: F 20x9J ET25 / R 20x10J ET30
Recommended setup: Nitron adjustable coilovers; 19-inch forged alloy wheels; AP Racing performance brakes; Michelin Pilot Sport 4S (F: 225/40 R19, R: 255/35 R19). Note: CX-generation flagship powered by a BMW 3.0L turbocharged inline-6 engine (335 hp).
Economy impact: Significant increase
Best for: Show builds, weekend cars
Appearance 10/10 | Comfort 3/10 | Install difficulty ★★★★
Estimated cost range: $$$$$
Performance Comparison Matrix
| Wheel Spec | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 18x8J ET35 | F 18.5x8.5J ET32 / R 18.5x9.5J ET35 | F 19x8.5J ET28 / R 19x9.5J ET35 | F 19.5x9J ET27 / R 19.5x10J ET33 | F 20x9J ET25 / R 20x10J ET30 |
| Economy Impact | None | Minimal | Slight increase | Noticeable increase | Significant increase |
| Appearance | 5/10 | 6/10 | 8/10 | 9/10 | 10/10 |
| Comfort | 10/10 | 9/10 | 7/10 | 5/10 | 3/10 |
| Install Difficulty | ★☆☆☆ | ★☆☆☆ | ★★☆☆ | ★★★☆ | ★★★★ |
| Cost Range | $$ (OE replacement) | $$ - $$$ | $$$ | $$$$ | $$$$$ |
| Best For | Daily drivers, warranty-conscious owners | Owners who want a mild upgrade with no compromise | Enthusiasts wanting a flush look daily | Show-and-drive builds | Show builds, weekend cars |
Real-World Reference Cases
The following builds are compiled from typical ANKUSI customer configurations for this platform and are illustrative, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Commuter prioritizing comfort and reliability.
Setup: F 18x8J ET35 / R 18x9J ET35 forged wheels, factory suspension.
Cost: $$ (OE replacement)
Outcome: No clearance issues, factory ride quality retained.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Weekend driver wanting a flush stance without sacrificing daily usability.
Setup: F 19x8.5J ET28 / R 19x9.5J ET35 forged wheels.
Cost: $$$
Outcome: Flush fitment with acceptable ride comfort for daily use.
Case 3: Show Build (Max Aggressive)
Profile: Show-and-shine build prioritizing stance over comfort.
Setup: F 20x9J ET25 / R 20x10J ET30 forged wheels. Nitron adjustable coilovers; 19-inch forged alloy wheels; AP Racing performance brakes; Michelin Pilot Sport 4S (F: 225/40 R19, R: 255/35 R19). Note: CX-generation flagship powered by a BMW 3.0L turbocharged inline-6 engine (335 hp).
Cost: $$$$$
Outcome: Maximum aggressive stance; clearance verified case-by-case.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.
- OE 18x8J ET35: backspacing ≈ 5.88"
- Flush 19x8.5J ET28: backspacing ≈ 5.85"
- Max 20x9J ET25: backspacing ≈ 5.98"
Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your Morgan Plus Six.