Mini OEM-Style Brushed Silver 10-Spoke Forged Wheels
Mini Countryman / Paceman ALL4 Fitment · 5-Lug
2024 Mini Countryman SE ALL4 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Mini Countryman SE ALL4 wheels? This page gives the 2024 Mini Countryman SE ALL4 bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Mini Countryman SE ALL4 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2024 Mini Countryman SE ALL4 uses a 5x112 bolt pattern with a 66.6 mm centre bore and M14x1.25 lug bolts. Factory wheels: 19x8J at ET46. For aftermarket wheels, 20x9J ET35 sits flush and 21x9.5J ET30 is the most aggressive fit.
Forged wheels for the 2024 Mini Countryman SE ALL4 — drilled 5x112 with a 66.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in about 25 days.
Get a quote for this car
Mini Countryman SE ALL4 (2024): 5x112 bolt pattern, 66.6mm center bore. Factory wheels: 19x8J. Reference fitment ranges.
Bolt Pattern5x112
Wheel Bolt/NutM14x1.25 Bolt
Center Bore66.6mm
Wheel Load Rating1035–1438 kg/wheel (SUV segment reference)
Year2024
CategoryEV SUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Built to order by ANKUSI — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x8J at ET46 |
| Flush Fitment | 20x9J at ET35 offset |
| Maximum Aggressive | 21x9.5J at ET30 offset |
Forged wheels for the Mini Countryman SE ALL4Machined to the 5x112 bolt pattern and 66.6 mm bore · 14–24 inch · offset calculated for your car · 3D drawing before production
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Mini Countryman SE ALL4 runs a 5x112 bolt pattern, 66.6mm center bore, and a 19x8J at ET46, front and rear, wheel from the factory. Our Flush Fitment reference is 20x9J ET35, which tucks the tire under the fender lip on a stock-height Mini Countryman SE ALL4. Our Maximum Aggressive reference is 21x9.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Mini Countryman SE ALL4 OE Wheel Specs
The 2024 Mini Countryman SE ALL4 (EV SUV) uses a 5x112 bolt pattern with a 66.6mm center bore. Factory wheels are 19x8J at ET46.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Mini Countryman SE ALL4 (2024) we drill the 5x112 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look with minimal rubbing, 20x9J ET35 is the recommended starting point on a stock or mildly lowered Mini Countryman SE ALL4.
Maximum Aggressive Fitment
21x9.5J ET30 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
Real-World Fitment Notes
Air lowering links; 20x9.0J ET35 Vossen HF-5 wheels; regenerative brakes; Hankook iON evo EV tires 245/40 R20. Note: Fully electric dual-motor all-wheel-drive compact luxury SUV.
5-Tier Configuration Options
A Factory-Style 19x8.0J ET46
Recommended setup: 19x8.0J ET46 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,200-1,500 (wheels + tires + install)
B Comfortable Upgrade 20x8.5J ET41
Recommended setup: 20x8.5J ET41 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 20x9.0J ET35
Recommended setup: 20x9.0J ET35 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 21x9.5J ET33
Recommended setup: 21x9.5J ET33 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 21x9.5J ET30
Recommended setup: 21x9.5J ET30 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 19x8.0J ET46 | 20x8.5J ET41 | 20x9.0J ET35 | 21x9.5J ET33 | 21x9.5J ET30 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $1,200-1,500 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 19x8.0J ET46
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 20x9.0J ET35
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 21x9.5J ET30
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
1
What's your primary use? Daily commuting → Tier A/B. Weekend street driving → Tier B/C. Show or occasional track use → Tier D/E.
2
What's your budget? Under $800 → Tier A. $800-3,400 → Tier B/C. $3,400+ → Tier D/E.
3
How much does fuel economy matter? Very important → Tier A. Somewhat important → Tier B/C. Not a priority → Tier D/E.
4
Still unsure? Tier C (Balanced / Flush Fit) is the default choice for most Mini Countryman SE ALL4 owners.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 19x8J ET46 → ~6.31″ backspacing
- Flush: 20x9J ET35 → ~6.38″ backspacing
- Max: 21x9.5J ET30 → ~6.43″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Mini spec, or want a wheel built to a custom offset for your Mini Countryman SE ALL4? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Custom Forged Wheels for the Mini Countryman SE ALL4 (2024)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x112 pattern and the 66.6mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose — most Mini orders on this platform land somewhere between the 20x9J ET35 flush setup and the 21x9.5J ET30 aggressive setup referenced above.
Designs we already tool for the 5x112 pattern — each one is re-cut to your sizes and offsets:
Mini OEM-Style Brushed Silver 10-Spoke Forged Wheels – Mini Countryman / Paceman ALL4 Fitment (5-Lug)
Mini OEM-Style Bronze Deep Lip Forged Wheels – Mini Cooper / Clubman ALL4 Fitment (5-Lug)
Mini OEM-Style Gloss Black Directional Machined Face Forged Wheels – Mini Countryman / Paceman ALL4 Fitment (5-Lug)
Mini OEM-Style Gloss Black 10-Spoke Forged Wheels – Mini Cooper / Clubman Fitment (5-Lug)Frequently Asked Questions
What bolt pattern (PCD) does the Mini Countryman SE ALL4 use?
The 2024 Mini Countryman SE ALL4 uses a 5x112 bolt pattern.
How many lug bolts does the Mini Countryman SE ALL4 use?
The Mini Countryman SE ALL4 uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Mini Countryman SE ALL4?
The Mini Countryman SE ALL4's center bore is 66.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Mini Countryman SE ALL4?
Factory wheels on the Mini Countryman SE ALL4 are 19x8J at ET46.
What is the biggest wheel size I can fit on my Mini Countryman SE ALL4 without rubbing?
The most aggressive fitment we recommend without fender work is 21x9.5J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Mini Countryman SE ALL4?
For a flush look with minimal to no rubbing, we recommend 20x9J at ET35 offset as a starting point on a stock or mildly lowered Mini Countryman SE ALL4.
Do I need wheel spacers for my Mini Countryman SE ALL4?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Mini Countryman SE ALL4?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.38" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Mini Countryman SE ALL4?
The Mini Countryman SE ALL4 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Vehicles With the Same Hub as the Mini Countryman SE ALL4 (5x112, 66.6 mm Bore)
In our database, 823 other vehicle entries from 21 makes use exactly the same 5x112 bolt pattern and 66.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 58.6% of those also use a 66.6 mm center bore.
Hub-Centric Rings for a 66.6 mm Center Bore
A wheel with a center bore larger than 66.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 67.1 mm | 67.1 → 66.6 mm |
| 70.1 mm | 70.1 → 66.6 mm |
| 70.5 mm | 70.5 → 66.6 mm |
| 71.6 mm | 71.6 → 66.6 mm |
| 73.1 mm | 73.1 → 66.6 mm |
ANKUSI forged wheels are bored to exactly 66.6 mm for this vehicle, so no ring is needed.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x8 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Forged Wheel Designs for the Mini Countryman SE ALL4
Every design below is forged to order, so it can be machined to the Mini Countryman SE ALL4's 5x112 bolt pattern and 66.6 mm center bore, with the width and offset calculated for your setup.
Mini OEM-Style Bronze Deep Lip Forged Wheels
Mini Cooper / Clubman ALL4 Fitment · 5-Lug
BBS RI-D-Style Full Polished Silver 5-Spoke Y-Design Forged Wheels
BMW M3 CS Handschalter Fitment · 19-21in, 5x112
HRE FF01-Style Gloss Black 5-Spoke Y-Design Forged Wheels
BMW M3 CS Handschalter Fitment · 19-21in, 5x112
Mini OEM-Style Gloss Black Directional Machined Face Forged Wheels
Mini Countryman / Paceman ALL4 Fitment · 5-Lug
Mini OEM-Style Gloss Black 10-Spoke Forged Wheels
Mini Cooper / Clubman Fitment · 5-Lug
BMW M2 G87 / M3 G80 Forged Wheels
Bronze Mesh
Rolls-Royce Ghost / Wraith Forged Wheels
Brushed Silver Slotted Dish
Bolt pattern and center bore on this page were cross-checked against at least two independent sources before publication. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.