
Gloss Black Y-Spoke Mesh Forged Wheels
Monoblock · Gloss Black
Fitting Kia ProCeed wheels? This page gives the 2019 Kia ProCeed bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Kia ProCeed rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Kia ProCeed — styles, sizes & factory quote →
Kia ProCeed (2019): 5x114.3 bolt pattern, 67.1mm center bore. Factory wheels: 18x7.5J F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x7.5J F/R |
| Flush Fitment | 19x8.5J at ET40 offset |
| Maximum Aggressive | 19x9.0J at ET35 offset |
Every design below is forged to order, so it can be machined to the Kia ProCeed's 5x114.3 bolt pattern and 67.1 mm center bore, with the width and offset calculated for your setup.

Monoblock · Gloss Black

Monoblock · Polished

Replica · Copper

Monoblock · Bronze

Monoblock · Satin Black

Monoblock · Bright Silver


Monoblock · Gloss Black
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


Wagons split the difference between sedan agility and load-carrying duty, and the wheels have to serve both roles. A forged wheel holds the same structural margin as the factory piece while trimming rotational weight, which benefits both the empty-car handling and the loaded-car ride.
The Kia ProCeed runs a 5x114.3 bolt pattern, 67.1mm center bore, and a 18x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.5J ET40, which tucks the tire under the fender lip on a stock-height Kia ProCeed. Our Maximum Aggressive reference is 19x9.0J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2019 Kia ProCeed (Shooting Brake) uses a 5x114.3 bolt pattern with a 67.1mm center bore. Factory wheels are 18x7.5J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Kia ProCeed (2019) we drill the 5x114.3 pattern and cut the centre bore to 67.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Kia spec, or want a wheel built to a custom offset for your Kia ProCeed? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 107-127 Nm (79-94 ft-lb). Range covers most Kia passenger cars and crossovers on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.