Forgestar-Style Gloss Black 9-Spoke Beadlock Forged Wheels
Off-Road Beadlock · Gloss Black
2026 Karma Gyesera Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Karma Gyesera wheels? This page gives the 2026 Karma Gyesera bolt pattern (5x120), centre bore, factory rim size and the offset range for aftermarket and forged Karma Gyesera rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2026 Karma Gyesera uses a 5x120 bolt pattern with a 67.1 mm centre bore. For aftermarket wheels, 21x9.5J ET25 front / 21x10.5J ET30 rear sits flush.
Forged wheels for the 2026 Karma Gyesera — drilled 5x120 with a 67.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Karma Gyesera (2026): 5x120 bolt pattern, 67.1mm center bore, OE F 21x8.5J ET35 / R 21x9.5J ET40. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x120
Center Bore67.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2026
Category5-Lug Performance / Tuner
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 21x9.5J ET25 / R 21x10.5J ET30 |
Forged Wheel Designs for the Karma Gyesera
Every design below is forged to order, so it can be machined to the Karma Gyesera's 5x120 bolt pattern and 67.1 mm center bore, with the width and offset calculated for your setup.
HRE-Style Bright Silver 5 Y-Spoke Concave Forged Wheels
Concave · Bright Silver
Corvette OEM-Style Black Chrome 5 Y-Spoke Forged Wheels
Monoblock · Black Chrome
Kansei-Style Polished 5-Spoke Star Concave Forged Wheels
Concave · Polished
Platinum Bright Silver Full-Face Forged Wheels
Monoblock · Bright Silver
Forgiato Bright Silver Full-Face Forged Wheels
Replica · Bright Silver
Vossen-Style Gloss Black 5 Y-Spoke Forged Wheels
Monoblock · Gloss Black
Polished 5-Spoke Retro Flat Dish Forged Wheels
Off-Road · Polished
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Most of the engineering value in a forged wheel over a cast one shows up in rotational mass, not outright strength — both can meet the same load rating, but the forged piece gets there lighter. On a sedan platform tuned for everyday balance, that weight saving is felt directly in steering response and ride quality.
The Karma Gyesera ships from the factory on a 5x120 bolt pattern with a 67.1mm center bore and a F 21x8.5J ET35 / R 21x9.5J ET40 wheel. Our flush reference for the Karma Gyesera is F 21x9.5J ET25 / R 21x10.5J ET30.; our maximum aggressive reference is F 22x9.5J ET20 / R 22x11J ET25. — beyond that, expect clearance issues against the fender liner without further modification.
Karma Gyesera OE Wheel Specs
The Karma Gyesera ships from the factory on 5x120 bolt pattern wheels with a 67.1mm center bore. The stock wheel size is F 21x8.5J ET35 / R 21x9.5J ET40, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Karma Gyesera (2026) we drill the 5x120 pattern and cut the centre bore to 67.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 21x8.5J | ET35 | 6.13 in (156 mm) | — | — |
| Flush | 21x9.5J | ET25 | 6.23 in (158 mm) | +3 mm | +23 mm |
| Maximum | 22x9.5J | ET20 | 6.04 in (153 mm) | −2 mm | +28 mm |
Vehicles With the Same Hub as the Karma Gyesera (5x120, 67.1 mm Bore)
In our database, 10 other vehicle entries from 5 makes use exactly the same 5x120 bolt pattern and 67.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x120 is used by 10.3% of the vehicle pages in our English fitment guide (670 of 6,503); 1.6% of those also use a 67.1 mm center bore.
Hub-Centric Rings for a 67.1 mm Center Bore
A wheel with a center bore larger than 67.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 70.1 mm | 70.1 → 67.1 mm |
| 70.5 mm | 70.5 → 67.1 mm |
| 71.6 mm | 71.6 → 67.1 mm |
| 72.6 mm | 72.6 → 67.1 mm |
| 73.1 mm | 73.1 → 67.1 mm |
ANKUSI forged wheels are bored to exactly 67.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Karma Gyesera use?
The 2026 Karma Gyesera uses a 5x120 bolt pattern.
How many lug bolts does the Karma Gyesera use?
The Karma Gyesera uses a 5-lug bolt pattern (5x120), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Karma Gyesera?
The Karma Gyesera's center bore is 67.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the Karma Gyesera?
For a flush look with minimal to no rubbing, we recommend F 21x9.5J ET25 / R 21x10.5J ET30 as a starting point on a stock or mildly lowered Karma Gyesera.
Do I need wheel spacers for my Karma Gyesera?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Karma Gyesera?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.23" backspacing up front and 6.93" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Karma Gyesera?
Yes — the Karma Gyesera's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 21x8.5 wheels · 21 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.