MMX Design Polished 5-Spoke Forged Wheels
H-Type · Polished
2023 Ford Ranger Tremor Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ford Ranger Tremor wheels? This page gives the 2023 Ford Ranger Tremor bolt pattern (6x139.7), centre bore, factory rim size and the offset range for aftermarket and forged Ford Ranger Tremor rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Ford Ranger Tremor (2023): 6x139.7 bolt pattern, 93.1mm center bore. Factory wheels: 17x8.0J F/R. Reference fitment ranges.
Bolt Pattern6x139.7
Wheel Bolt/Nut1/2\"x20 Nut
Center Bore93.1mm
Wheel Load Rating1000–1400 kg/wheel (Pickup / Light Truck segment reference)
Year2023
CategoryPickup
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x8.0J F/R |
| Flush Fitment | 17x9.0J at ET18 offset |
| Maximum Aggressive | 18x9.5J at ET12 offset |
Forged Wheel Designs for the Ford Ranger Tremor
Every design below is forged to order, so it can be machined to the Ford Ranger Tremor's 6x139.7 bolt pattern and 93.1 mm center bore, with the width and offset calculated for your setup.
DT Forge Pink & Chrome Multi-Spoke Wheels
H-Type · Pink / Chrome
American Force Polished Multi-Spoke Wheels
H-Type · Polished
KG1 Forged Radar Polished Forged Wheels
H-Type · Polished
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Payload and towing figures on a truck are engineered around a specific unsprung mass budget at each corner. Forging lets ANKUSI hit the factory strength rating for the Ford Ranger Tremor at a lower rotational weight than an equivalent cast wheel, which is the more meaningful upgrade on a work-capable platform than diameter alone.
The Ford Ranger Tremor runs a 6x139.7 bolt pattern, 93.1mm center bore, and a 17x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 17x9.0J ET18, which tucks the tire under the fender lip on a stock-height Ford Ranger Tremor. Our Maximum Aggressive reference is 18x9.5J ET12 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Ford Ranger Tremor OE Wheel Specs
The 2023 Ford Ranger Tremor (Pickup) uses a 6x139.7 bolt pattern with a 93.1mm center bore. Factory wheels are 17x8.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ford Ranger Tremor (2023) we drill the 6x139.7 pattern and cut the centre bore to 93.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 17x8.0J ET55 → ~6.67″ backspacing
- Flush: 17x9.0J ET18 → ~5.71″ backspacing
- Max: 18x9.5J ET12 → ~5.72″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ford spec, or want a wheel built to a custom offset for your Ford Ranger Tremor? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford Ranger Tremor use?
The 2023 Ford Ranger Tremor uses a 6x139.7 bolt pattern.
How many lug bolts does the Ford Ranger Tremor use?
The Ford Ranger Tremor uses a 6-lug bolt pattern (6x139.7), so you need a 6-lug forged wheel to bolt straight on.
What is the center bore size on the Ford Ranger Tremor?
The Ford Ranger Tremor's center bore is 93.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ford Ranger Tremor?
Factory wheels on the Ford Ranger Tremor are 17x8.0J F/R.
What is the biggest wheel size I can fit on my Ford Ranger Tremor without rubbing?
The most aggressive fitment we recommend without fender work is 18x9.5J at ET12 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ford Ranger Tremor?
For a flush look with minimal to no rubbing, we recommend 17x9.0J at ET18 offset as a starting point on a stock or mildly lowered Ford Ranger Tremor.
Do I need wheel spacers for my Ford Ranger Tremor?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ford Ranger Tremor?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.71" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ford Ranger Tremor?
The Ford Ranger Tremor runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M14x1.5, conical-seat lug nut.
Factory Torque Spec: 135 Nm (100 ft-lb). Ford Ranger (current generation) spec on M14x1.5 studs; earlier Ranger generations used M12x1.5 or M14x2.0 threads, confirm for your exact model year.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.