Gloss Black 10-Spoke Polished-Lip Beadlock Forged Wheels
Off-Road Beadlock · Custom Finish
2001 Ford Mustang Bullitt GT Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ford Mustang Bullitt GT wheels? This page gives the 2001 Ford Mustang Bullitt GT bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Ford Mustang Bullitt GT rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2001 Ford Mustang Bullitt GT uses a 5x114.3 bolt pattern with a 70.5 mm centre bore. Factory wheels: 17x8.0J, front and rear. For aftermarket wheels, 18x9.0J ET38 sits flush and 19x9.5J ET35 is the most aggressive fit.
Forged wheels for the 2001 Ford Mustang Bullitt GT — drilled 5x114.3 with a 70.5 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Ford Mustang Bullitt GT (2001): 5x114.3 bolt pattern, 70.5mm center bore. Factory wheels: 17x8.0J F/R. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/Nut1/2\"x20 Nut
Center Bore70.5mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2001
CategoryCoupe
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x8.0J F/R |
| Flush Fitment | 18x9.0J at ET38 offset |
| Maximum Aggressive | 19x9.5J at ET35 offset |
Forged Wheel Designs for the Ford Mustang Bullitt GT
Every design below is forged to order, so it can be machined to the Ford Mustang Bullitt GT's 5x114.3 bolt pattern and 70.5 mm center bore, with the width and offset calculated for your setup.
Ford OEM-Style Brushed Silver Forged Wheels
Replica · Brushed Silver
Weld Racing-Style Black / Milled 10-Window Polished-Lip Forged Drag Racing Wheels
Drag Racing · Polished
Ford Mustang OEM-Style Matte Bronze 5-Spoke Dish Forged Wheels
Monoblock · Matte Bronze
Black / Machined 10-Spoke Beadlock Forged Wheels
Off-Road Beadlock · Custom Finish
Gloss Black 10-Spoke Mesh Red-Ring Forged Wheels
Off-Road Beadlock · Gloss Black
Weld Racing-Style Gloss Black / Machined Mesh Beadlock Forged Drag Racing Wheels
Drag Racing · Gloss Black / Machined
Absolute Forged-Style Gloss Black 10-Spoke Beadlock Forged Wheels
Off-Road Beadlock · Gloss Black
See all Ford Mustang wheel designs Ford OEM-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a performance-oriented coupe, the wheel is one of the few components where shaving weight has a compounding effect — less rotational mass means less work for the brakes, the drivetrain, and the chassis on every input. A forged wheel gets there without compromising the strength margin the factory engineered in.
The Ford Mustang Bullitt GT runs a 5x114.3 bolt pattern, 70.5mm center bore, and a 17x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x9.0J ET38, which tucks the tire under the fender lip on a stock-height Ford Mustang Bullitt GT. Our Maximum Aggressive reference is 19x9.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Ford Mustang Bullitt GT OE Wheel Specs
The 2001 Ford Mustang Bullitt GT (Coupe) uses a 5x114.3 bolt pattern with a 70.5mm center bore. Factory wheels are 17x8.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday drivability
- A commonly used size for this vehicle class, supporting parts and tire availability
- Maintains clearance for the factory suspension and brake components
- Provides stable, predictable handling across normal driving conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ford Mustang Bullitt GT (2001) we drill the 5x114.3 pattern and cut the centre bore to 70.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 17x8.0J ET45 → ~6.27″ backspacing
- Flush: 18x9.0J ET38 → ~6.5″ backspacing
- Max: 19x9.5J ET35 → ~6.63″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ford spec, or want a wheel built to a custom offset for your Ford Mustang Bullitt GT? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Ford Mustang Bullitt GT (5x114.3, 70.5 mm Bore)
In our database, 155 other vehicle entries from 6 makes use exactly the same 5x114.3 bolt pattern and 70.5 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 12.0% of those also use a 70.5 mm center bore.
Hub-Centric Rings for a 70.5 mm Center Bore
A wheel with a center bore larger than 70.5 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 71.6 mm | 71.6 → 70.5 mm |
| 72.6 mm | 72.6 → 70.5 mm |
| 73.1 mm | 73.1 → 70.5 mm |
| 74.1 mm | 74.1 → 70.5 mm |
ANKUSI forged wheels are bored to exactly 70.5 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford Mustang Bullitt GT use?
The 2001 Ford Mustang Bullitt GT uses a 5x114.3 bolt pattern.
How many lug bolts does the Ford Mustang Bullitt GT use?
The Ford Mustang Bullitt GT uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ford Mustang Bullitt GT?
The Ford Mustang Bullitt GT's center bore is 70.5mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ford Mustang Bullitt GT?
Factory wheels on the Ford Mustang Bullitt GT are 17x8.0J F/R.
What is the biggest wheel size I can fit on my Ford Mustang Bullitt GT without rubbing?
The most aggressive fitment we recommend without fender work is 19x9.5J at ET35 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ford Mustang Bullitt GT?
For a flush look with minimal to no rubbing, we recommend 18x9.0J at ET38 offset as a starting point on a stock or mildly lowered Ford Mustang Bullitt GT.
Do I need wheel spacers for my Ford Mustang Bullitt GT?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ford Mustang Bullitt GT?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.5" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ford Mustang Bullitt GT?
The Ford Mustang Bullitt GT runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 136 Nm (100 ft-lb). Covers most Ford passenger cars and crossovers (Fusion, Focus, Escape and similar) on M12x1.5 studs.
TPMS: Vehicles built before the 2008 model year were not federally required to carry factory TPMS in the US, though many manufacturers adopted it earlier; verify whether your specific build has TPMS before ordering sensor-compatible wheels.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 17x8 wheels · 17 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.